BendPak MD-6XP Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

background image

MD-6XP Mid-Rise Scissor Lift

18

P/N 5900108 — Rev. F — March 2020

Connect the Hydraulic Hoses

Hydraulic Hoses provide Hydraulic Fluid to the Hydraulic Cylinders, where it is used to raise the

Platform.
The MD-6XP comes with two Hydraulic Hose lengths:
•

Short Hydraulic Hose

. Connects the two Hydraulic Cylinders on the Lift.

•

Long Hydraulic Hose

. Connects from the closest Hydraulic Cylinder to the Power Unit.

The Power Unit can be placed on either side of the Frame, as long as the operator has an
unobstructed view of the Lift

at all times

.

The following drawing shows how to route the Hydraulic Hoses on the Lift.

Drawing shows Power Unit on the left side of the Frame. Drawing not to scale. Some components not

shown, other components exaggerated for clarity.

To connect the Hydraulic Hoses

:

1.

Locate the Long Hydraulic Hose and a Hydraulic Straight Fitting.

2.

Clean the Hydraulic components using the information in

Hydraulic Fluid Contamination

3.

The Short Hydraulic Hose is shipped from the factory already connected between the Hydraulic

Cylinders.

If it is not

, remove the Shipping Plugs from the Hydraulic Hose Ports near the bottom of each

Hydraulic Cylinder on the Lift, attach Hydraulic Elbow Fittings (04 JIC – 04 NPT) to the inside

Hydraulic ports, and then connect the Short Hydraulic Hose to the Elbow Fittings you just

attached, making sure to route the Hose through the Retaining Ring near the top of the Hydraulic
Cylinders.
Make sure to keep the Hydraulic Cylinder Ports and Fittings contaminant-free.

«
...
16
17
18
19
20
...
»

Содержание MD-6XP













































Отзывы:

Нет отзывов

Похожие инструкции для MD-6XP

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды