BendPak MD-6XP Скачать руководство пользователя страница 12

Страница: 12 / 44

MD-6XP Mid-Rise Scissor Lift

P/N 5900108 — Rev. F — March 2020

Select a Site

The MD-6XP is portable, so you may be moving it and using it at a variety of locations. Keep the

following in mind when selecting a location for your Lift:
•

Clearance

. You must have adequate space on all sides, plus enough space above for the

Vehicles you will be raising. See

Clearance Around the Lift

for more information.

•

Check for overhead obstructions

. Check for overhead obstructions such as building

supports, heaters, electrical lines, low ceilings, hanging lights, and so on.

You do not want the

Vehicles on the Lift hitting obstructions

•

Operator

. The operator

must

have a full, unobstructed view of the Lift.

•

Level Floor

. Only install the Lift on a dry, flat, and stable floor; do not install the Lift on dirt or an

uneven surface.

•

Power

. You will need a 115 VAC or 220 VAC power source available near the Power Unit.

•

Operating temperature

. The Lift is designed to be used between temperatures of 41º to 104ºF

(5º to 40ºC).

•

Outdoor use

. The Lift is best not left outside for long periods of time. If you want to use it

outside, BendPak recommends moving it outside, using it, then moving it back inside.

⚠

DANGER

Keep the Power Unit away from damp environments; the motor must

not

get wet.

•

Dress properly

. Always wear protective gear when installing the Lift. Leather gloves, steel-toed

work boots, eye protection, back belts, and hearing protection

are mandatory

. Do

not

wear

loose clothing or jewelry; contain long hair; keep hair, clothing, and gloves away from moving parts.

⚠

WARNING

You

must

wear OSHA-approved (publication 3151) Personal Protective Equipment

at all times

when using the Lift.

Planning for Electrical Work (220 VAC only)

If you received a Power Unit configured for 220 VAC operation (must’ve been specified at the time of

ordering), you will need to have a licensed, certified Electrician at some point in the installation.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician.

A Power Unit configured for 220 VAC operation is shipped with a pigtail for wiring to the power source.

Have your Electrician remove the pigtail and wire from inside the Electrical Box on the Power Unit to an

appropriate Power Cord and Plug.

Note

The Power Cord and Plug are

not

supplied with the Lift.

Содержание MD-6XP












































Результаты поиска

Содержание MD-6XP

Отзывы:

Похожие инструкции для MD-6XP

Бренды по названию

Популярные бренды

BendPak MD-6XP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MD-6XP

Отзывы:

Похожие инструкции для MD-6XP

Бренды по названию

Популярные бренды