manualshive.com logo in svg

BendPak HD-7500BL, Инструкция по установке и эксплуатации

BendPak HD-7500BL - ручное подъемное оборудование для автомобилей. Бесплатно загрузите Руководство по монтажу и эксплуатации на нашем сайте. Узнайте как правильно устанавливать и использовать этот мощный инструмент для подъема автомобилей. Скачайте руководство сейчас с manualshive.com.

Поделиться
Скачать
background image

4

TABLE OF CONTENTS

Contents                                                                                  Page No.

Warranty / Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Definitions of Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Owner’s Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installer Operator/ Protective Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety / Warning Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Step 1 / Selecting Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Step 2 / Floor Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Concrete Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Assembly View / Description of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Floor Plan / Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12

Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Power Unit Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Step 3 / Column and Cross Tube Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-16
Step 4 / Raising the Cross Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Step 5 / Powerside Runway Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Step 6 / Offside Runway Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Cable Routing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-20
Step 7 / Sheave Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Step 8 / Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
Step 9 / Power Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-24
Step 10 / Routing Hydraulic Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Step 11 / Routing Air Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Safety Air Line Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Step 12 / Power Unit Hook Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-30
Step 13 / Inspecting Slack Safety Springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Step 14 / Lift Start Up / Final Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-31
Step 15 / Anchoring The Columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-32
Step 16 / Attaching Approach Ramps / Tire stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Step 17 / Leveling / Synchronizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Step 18 / Bleeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34
Step 19 / Operation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Step 20 / Lift Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-36
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-37
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-45
Grease Port Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Maintenance Records  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Part Number Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-66

Содержание HD-7500BL





































































Отзывы:

Нет отзывов

Похожие инструкции для HD-7500BL

3M DBI SALA Pro Series User Instructions preview
DBI SALA Pro Series
Бренд: 3M Страницы: 24
National Instruments NI 9381 Getting Started preview
NI 9381
Бренд: National Instruments Страницы: 9
Migatronic FOCUS 200 AC/DC PFC User Manual preview
FOCUS 200 AC/DC PFC
Бренд: Migatronic Страницы: 66
GYS 070820 Operating Manual preview
070820
Бренд: GYS Страницы: 40
Dannmar D-12 Series User Manual preview
D-12 Series
Бренд: Dannmar Страницы: 40
ICP DAS USA PISO-DA2U Quick Start Manual preview
PISO-DA2U
Бренд: ICP DAS USA Страницы: 7
EWM T4.04 Operating Instructions Manual preview
T4.04
Бренд: EWM Страницы: 54
Jazz JZ20-T10 User Manual preview
JZ20-T10
Бренд: Jazz Страницы: 12
IMS PULSEMIG 270 Manual preview
PULSEMIG 270
Бренд: IMS Страницы: 44
morse MORStak 611 Series Operator'S Manual preview
MORStak 611 Series
Бренд: morse Страницы: 9
Lincoln Electric PF44 Operator'S Manual preview
PF44
Бренд: Lincoln Electric Страницы: 56
JVC EX-D5 Instructions Manual preview
EX-D5
Бренд: JVC Страницы: 92
SMC Networks ZXP7 11-X1 Series Operation Manual preview
ZXP7 11-X1 Series
Бренд: SMC Networks Страницы: 32
Jasic MIG250P Manual preview
MIG250P
Бренд: Jasic Страницы: 30
Jasic JVM180i Manual preview
JVM180i
Бренд: Jasic Страницы: 40
IntelligentAg TP-link Instruction Manual preview
TP-link
Бренд: IntelligentAg Страницы: 11
IntelligentAg Recon Blockage Plus Operator'S Manual preview
Recon Blockage Plus
Бренд: IntelligentAg Страницы: 26
Bimba PCS User Manual preview
PCS
Бренд: Bimba Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды