manualshive.com logo in svg

BendPak HD-7500BL, Инструкция по установке и эксплуатации

BendPak HD-7500BL - ручное подъемное оборудование для автомобилей. Бесплатно загрузите Руководство по монтажу и эксплуатации на нашем сайте. Узнайте как правильно устанавливать и использовать этот мощный инструмент для подъема автомобилей. Скачайте руководство сейчас с manualshive.com.

Поделиться
Скачать
background image

34

POST-INSTALLATION CHECK-OFF

n

     Columns properly shimmed and stable 

n

     Anchor Bolts tightened 

n

     Pivot / Sheave Pins properly attached

  

n 

Electric power supply confirmed 

n

     Cables adjusted properly 

n

     Safety Locks functioning properly

n

     Check for hydraulic leaks

n

     Oil level

n

     Lubrication of critical components

n

     Check for overhead obstructions

n

     All Screws, Bolts, and Pins securely fastened

n 

Surrounding area clean

n 

Operation, Maintenance and Safety Manuals

      on site.

n 

Perform an Operational Test with a typical vehicle

STEP 19

(Operation Instructions)

OWNER/EMPLOYER  RESPONSIBILITIES

The Owner/Employer:

• 

Shall ensure that lift operators are qualified and that they 

are trained in the safe use and operation of the lift using 
the manufacturer’s operating instructions; ALI/SM01-1, ALI 
Lifting it Right safety manual; ALI/ST-90 ALI Safety Tips 
card; ANSI/ALI ALOIM-2000, American National Standard 
for Automotive Lifts-Safety Requirements for Operation, 
Inspection and Maintenance; ALI/WL Series, ALI Uniform 
Warning Label Decals/Placards; and in the case of frame 
engaging lifts, ALI/LP-GUIDE, Vehicle 

Lifting Points/Quick Reference Guide for Frame Engaging 
Lifts.

•

 Shall establish procedures to periodically inspect the 

lift in accordance with the lift manufacturer’s instructions 
or ANSI/ALI ALOIM-2000, American National Standard 
for Automotive Lifts-Safety Requirements for Operation, 
Inspection and Maintenance; and The Employer shall 
ensure that lift inspectors are qualified and that they are 
adequately trained in the inspection of the lift.

•

 Shall establish procedures to periodically maintain the 

lift in accordance with the lift manufacturer’s instructions 
or ANSI/ALI ALOIM-2000, American National Standard 
for Automotive Lifts-Safety Requirements for Operation, 
Inspection and Maintenance; and The Employer shall 
ensure that lift maintenance personnel are qualified and 
that they are adequately trained in the maintenance of the 
lift.

• 

Shall maintain the periodic inspection and maintenance 

records recommended by the manufacturer or ANSI/ALI 
ALOIM-2000, American National Standard for Automotive 
Lifts-Safety Requirements for Operation, Inspection and 
Maintenance.

•

 Shall display the lift manufacturer’s operating 

instructions; ALI/SM 93-1, ALI Lifting It Right safety 
manual; ALI/ST-90 ALI Safety Tips card; ANSI/ALI AL-
OIM-2000, American National Standard for Automotive 
Lifts-Safety Requirements for Operation, Inspection and 
Maintenance; and in the case of frame engaging lifts, ALI/
LP-GUIDE, Vehicle Lifting Points/Quick Reference Guide 
for Frame Engaging Lifts; in a conspicuous location in the 
lift area convenient to the operator.

• 

Shall provide necessary lockout/tagout means for 

energy sources per ANSI Z244.1-1982 (R1993), Safety 
Requirements for the Lockout/Tagout of Energy Sources, 
before beginning any lift repairs.

•

 Shall not modify the lift in any manner without the prior 

written consent of the manufacturer.

STEP 20

(Lift Operation Safety)

WARNING!

Wheels Chock must be used on the rear wheels.

(See Fig 18.1)

Fig 18.1 

WARNING!

TO AVOID PERSONAL INJURY AND/OR PROPERTY 

DAMAGE, PERMIT ONLY TRAINED PERSONNEL TO 

OPERATE LIFT.  AFTER REVIEWING THESE INSTRUC-

TIONS, PRACTICE USING LIFT CONTROLS BY 

RUNNING THE LIFT THROUGH A FEW UNLOADED 

CYCLES BEFORE LOADING VEHICLE ON LIFT. 

NEVER

 

RAISE JUST ONE END, ONE CORNER, OR ONE SIDE 

OF VEHICLE.

Содержание HD-7500BL





































































Отзывы:

Нет отзывов

Похожие инструкции для HD-7500BL

TagMaster XT-3 Installation Manual & Data Sheet preview
XT-3
Бренд: TagMaster Страницы: 28
National Instruments PCIe-7846 User Manual preview
PCIe-7846
Бренд: National Instruments Страницы: 9
Atlas Copco BLG 30 Safety And Operating Instructions Manual preview
BLG 30
Бренд: Atlas Copco Страницы: 116
Safety Clamps VL-BC Operation, Maintenance, And Repair Manual preview
VL-BC
Бренд: Safety Clamps Страницы: 16
Velux KUX 100 Instructions Manual preview
KUX 100
Бренд: Velux Страницы: 11
QTS AN-X2-ABDHRIO User Manual preview
AN-X2-ABDHRIO
Бренд: QTS Страницы: 50
Paton Cooler-7 User Manual preview
Cooler-7
Бренд: Paton Страницы: 17
Riello 20116460 Instruction Booklet preview
20116460
Бренд: Riello Страницы: 2
Link LSR 90 Maintenance Instructions Manual preview
LSR 90
Бренд: Link Страницы: 11
Toa DP-0202 Operating Instructions Manual preview
DP-0202
Бренд: Toa Страницы: 12
zika I-DC 400 Owner'S Manual preview
I-DC 400
Бренд: zika Страницы: 13
Miller AXCESS 450 CE Owner'S Manual preview
AXCESS 450 CE
Бренд: Miller Страницы: 56
Lincoln Electric PRO MIG 180 Instruction Manual preview
PRO MIG 180
Бренд: Lincoln Electric Страницы: 32
Paton STANDARDTIG-160 User Manual preview
STANDARDTIG-160
Бренд: Paton Страницы: 115
Unitor UWW-161 TP Instruction Manual preview
UWW-161 TP
Бренд: Unitor Страницы: 32
Vestil CYL-P-LUG Series Instruction Manual preview
CYL-P-LUG Series
Бренд: Vestil Страницы: 7
FOG 442 9020 Manual preview
442 9020
Бренд: FOG Страницы: 72
JH Industries Copperloy EDGE-OF-DOCK SEL Series Installation & Owner'S Manual preview
Copperloy EDGE-OF-DOCK SEL Series
Бренд: JH Industries Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды