BendPak HD-7500BL Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 68

background image

28

All wiring must be performed by a certified electrician only.

DANGER!

DO NOT PERFORM ANY MAINTENANCE OR

INSTALLATION OF ANY COMPONENTS WITH OUT

FIRST ENSURING THAT ELECTRICAL POWER HAS

BEEN DISCONNECTED AT THE SOURCE OR PANEL

AND CANNOT BE RE-ENERGIZED UNTIL ALL

MAINTENANCE AND/OR INSTALLATION

PROCEDURES ARE COMPLETED.

SEE WIRING INSTRUCTIONS AFFIXED TO

MOTOR FOR PROPER WIRING INSTRUCTIONS.

Identify which Power Unit the lift was shipped with by looking on the data tag affixed to the Power
Unit motor head. if the model number begins with the letter “S” then use the “S” wiring diagrams.
If the model number begins with the letter “E” or “F” then use the “E” or “F” wiring diagrams.

IMPORTANT POWER-UNIT

INSTALLATION NOTES

n

DO NOT run power unit with no oil. Damage to pump can occur.

n

The power unit must be kept dry. Damage to power unit caused by water or other liquids such as

detergents, acid etc., is not covered under warranty.

n

Improper electrical hook-up can damage motor and will not be covered under warranty.

n

Motor can not run on 50HZ without a physical change in motor.

n

Use a separate breaker for each power unit.

n

Protect each circuit with time delay fuse or circuit breaker.

n

For 208-230 volt, single phase, use a 25 amp fuse.

n

For 208-230 volt, three phase, use a 20 amp fuse.

n

For 380-440 volt, three phase, use a 15 amp fuse.

Installation and adjustment.

DO NOT attempt to raise vehicle until a thorough operation check has been completed.

«
...
26
27
28
29
30
...
»

Содержание HD-7500BL





































































Отзывы:

Нет отзывов

Похожие инструкции для HD-7500BL

Бренд: Far Tools Страницы: 24

Бренд: VENCO Страницы: 4

MODULEX EXT Series

Бренд: Unical Страницы: 52

Бренд: R. Beck Maschinenbau Страницы: 34

Бренд: Laars Страницы: 9

Бренд: ENTRYPASS Страницы: 27

Бренд: WAGO Страницы: 12

TransTig 1750 Puls

Бренд: Fronius Страницы: 88

Robopac Rotoplat 3000LD

Бренд: AETNAGROUP Страницы: 87

Бренд: Lifter Страницы: 170

Бренд: WAGO Страницы: 50

Бренд: Worldwel Страницы: 5

Бренд: Curtis Instruments Страницы: 144

Бренд: Westweld Страницы: 18

Бренд: PVI Страницы: 12

Бренд: R-Tech Страницы: 17

MULTIWELD 250T-C

Бренд: ims PRO Страницы: 28

Бренд: IMS Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды