background image

12

Setting Up Your Multiviewer

Changing the Multiviewer’s IP Address from the Densité Control Panel

If the Status LED indicates an error condition, refer to your multiviewer’s Guide to 
Installation and Operation to find out what the other LEDs might be indicating.

13 Verify that the new IP address is effective, by referring to 

Finding the System IP Address 

and Application Version

, on page 13.

At this point, it is recommended to back up the new configuration to the controller’s 
non-volatile memory by saving a 

restore point

.

14 On the Densité frame’s local control panel, press the CONTROLLER button.

15 Press the [–] button repeatedly until RESTORE POINTS appears on the display, and then 

press the SEL button.

16 Press the [–] button repeatedly until SAVE A CARD appears on the display, and then 

press the SEL button.

17 Press the [–] button repeatedly until CARD # N—where N matches the slot number for 

the KMV-3901/3911 card whose configuration you wish to save—appears on the 
display, and then press the SEL button.

18 If you had to change the Densité controller’s default action from 

update settings

 to 

keep 

settings

 in order to configure your card’s network settings, then refer to 

Verifying the 

Densité Controller’s Restore-Point Settings

, on page 9 again, to revert the default 

action to 

update settings

.

Green

Blinking orange

Red

Blinking red

Normal

Booting (or the card is 
selected for local control)

No Ethernet / SD card 
error

Fan failure / no rear / 
duplicate IP address

Select button

Status LED

Boot LED,
Power LED,
CPU Status LED (other side of board)

SDI LEDs

USB connector (other side of board)

Содержание Miranda KMV-3901




























Отзывы: