Becker E12 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

Becker E12 Скачать руководство пользователя страница 7

Caution

Electrical connections may only be carried out by a qualified electrician. Prior to assembly,

the power supply must be disconnected and secured. Please give the enclosed connection

information to the responsible electrical contractor.

Calculate the space required at the side (M) by measuring the drive head (1) and wall bracket (2). The
clear dimension of the box (X) minus the space required at the side (M) and idler (G) gives the length
(L) of the barrel: L=X-M-G.

The space required at the side (M) varies depending on the combination of drive and wall bracket.

Then mount the wall bracket and idler. Ensure that the barrel is aligned at right angles to the wall and that sufficient axial play is al-
lowed for the mounted system.

Assembling and disassembling the mounting pin

Ø45, Ø58

When pushed in, the mounting pin (2) locks automatically. To undo the mounting pin (2), push the tab
washer (1) upwards and pull out the mounting pin (2).

Assembling and disassembling the drive adapter

Fitting the ring onto the thrust ring

Assembling the drive adapter with safety catch on the

drive shaft

Disassembling the drive adapter with safety catch on the

drive shaft

Assembling and disassembling the drive adapter with drive adapter safety catch or screw connection

Assembling and disassembling the drive
adapter with separate drive adapter
safety catch

Assembling and disassembling the drive
adapter with screw connection

Mounting the drive in the tube

For profile shafts:

In the case of some drive adapters, tolerances of the groove widths in different barrels can be offset by
rotating the drive adapter into a different groove recess. These groove recesses have different sizes
and allow the drive to fit exactly.

Y

X

For round shafts:

Measure the lug of the thrust ring (X, Y). Then notch the tube on the motor side, so the lug of the thrust
ring can also be pushed into the shaft. There must be no play between the lug of the thrust ring and the
shaft.

7 - en

«
...
5
6
7
8
9
...
»

Содержание E12





























Отзывы:

Нет отзывов