BC Biomedical DA-2006 Скачать руководство пользователя страница 56

Страница: 56 / 171

Running a Defibrillator Test

A Cardioversion Test is simply an energy test with special attention being given to the

timing. The DA-2006 continuously monitors for the R-wave timing and displays, if

possible, the delay between the R-wave and the pulse. In Cardioversion testing, the

Defibrillator is set to deliver a pulse based on a specific delay after the R-wave.

(1) Connect ECG leads to the corresponding universal connector on the DA-2006.

The connectors are marked with both the AHA and International color codes.

(2) Turn on the DA-2006.

(3) The unit will come up in the “High Range Defibrillator” mode. This range is used

for normal adult testing.

NOTE: If it is desirable to run a test at 50 Joules or less with a peak

voltage of 1000 Volts or less, the unit may be changed to the “Low Range

Defibrillator” mode using the key.

CARDIOVERSION TEST

WARNING

This section is provided as a guide to familiarize

the user with the DA-2006 Series. It is not

intended to provide the necessary test sequence

for every Defibrillator. The user must consult the

manufacturer’s manual for each DUT to

determine the correct test procedure to follow.

Содержание DA-2006












































































































































































Результаты поиска

Содержание DA-2006

Отзывы:

BC Biomedical DA-2006, Руководство по обслуживанию, Страница: 56 / 171

Результаты поиска

Содержание DA-2006

Отзывы: