BC Biomedical DA-2006 Скачать руководство пользователя страница 141

Страница: 141 / 171

B 2

OVERVIEW

The DA2006P energy pulse function is based on converting the output from a defibrillator to

a digital value. The defibrillator is discharged into a fixed 50 ohms non-inductive load. The

resulting voltage drop across this resistor is divided by a series of resistors and converted

from an analog voltage to a digital count by the analog-to-digital (A/D) converter. This value

is then processed by the microprocessor and displayed on the LCD. To properly evaluate

the defibrillator pulse, the A/D converter samples 10,000 times per second.

The pace pulse is also analyzed by an A/D converter. The load resistance for the pace

function can be the same load resistance for the defib pulse or a separate set of internal

load resistors can be used. This allows the user to be able to analyze the pace pulse at

many different loads.

ECG waveforms, along with performance waveforms are generated by an internal digital to

analog converter and are available on the ten patient lead connectors.

USER INTERFACE

The user interfaces with the analyzer via the 240x64 pixel Backlit LCD display and the

keys. The LCD display is a full graphical display and is continually updated to inform the

user of the current operating conditions. The seven keys allows the user the ability to setup

and operate the analyzer with a minimal number of keystrokes. The keys labeled F1

through F5 change function based on the current operating mode of the DA2006P. The

lower section of the display is used to identify the function of these keys at any given time.

Содержание DA-2006












































































































































































Результаты поиска

Содержание DA-2006

Отзывы:

BC Biomedical DA-2006, Руководство по обслуживанию, Страница: 141 / 171

Результаты поиска

Содержание DA-2006

Отзывы: