BC Biomedical DA-2006 Скачать руководство пользователя страница 25

Страница: 25 / 171

DA-2006 Series

General Operation

The unit is controlled by 7 light touch keys. They allow the user to move around within the

displayed parameters, select the desired options, choose a specific category and control

the setup for the unit. When a key is depressed there is an audio click when it is accepted,

or a razz tone if the key is invalid.

A large LCD graphics display with backlight provides the user with information about the

current status of the device configuration options, test results and more. The display

identifies the function of each key on a dynamic basis. As the operation mode changes,

the key functions change to suit the operating mode.

Range Key

The key scrolls through the ranges of the DA-2006 Series analyzers. Depressing

the key will allow the user to select between High Defibrillator Range (1000J max), Low

Defibrillator Range (50J max) and, with the DA-2006P, Pacemaker Range. The default

mode on power up is High Defibrillator Range.

Backlight Key

The Graphic LCD display may be viewed with or without the backlight. Depressing any key

will activate the backlight. However, since the backlight will drain the battery if left on, it will

automatically shut off after a user programmable delay when running on battery power.

The key is provided to toggle the backlight on or off at any time.

Содержание DA-2006












































































































































































Результаты поиска

Содержание DA-2006

Отзывы:

BC Biomedical DA-2006, Руководство по обслуживанию, Страница: 25 / 171

Результаты поиска

Содержание DA-2006

Отзывы: