BC Biomedical DA-2006 Скачать руководство пользователя страница 129

Страница: 129 / 171

This section looks at the layout of the DA-CS-06 and gives descriptions of the elements that
are present and shows how they should be connected.

OVERVIEW

Calibration Verification Software

PC-based program for control

and display of results to verify a

Defibrillator Analyzer falls within

the presented Standard.

Sample Defibrillator

NOTE: A specific Defibrillator

is not necessary to verify

the calibration of a

Defibrillator Analyzer to the

presented Standard

This is a sample of a

typical source.

Interface Module

Connects via a BNC cable

to the Calibration Standard
and via a USB cable to the

PC running the

Calibration Verification

Software

Calibration Standard

Plugs into the Input Jacks in

the center of the Defib

Plates on the Defibrillator

Analyzer and has a BNC

cable that is connected to

the Interface Module

Sample Defibrillator

Analyzer

NOTE: The Device Under Test

(DUT) must be Earth Grounded.

This is typically done through

the Serial Port.

Содержание DA-2006












































































































































































Результаты поиска

Содержание DA-2006

Отзывы:

BC Biomedical DA-2006, Руководство по обслуживанию, Страница: 129 / 171

Результаты поиска

Содержание DA-2006

Отзывы: