Bay Alarm Vista-20Bay Скачать руководство пользователя страница 62

Страница: 62 / 138

VISTA-20BAY Installation & Setup Guide

14–2

Entering Program Mode

You may use one of the following methods:

a) Press both [

✱

] and [#] at the same time within 50 seconds after power is applied to the

control, or

b) After power-up, enter

Installer code (4 1 1 2) + 8 0 0

This method is disabled if you exit the program mode using

✱

98 instead of

✱

99. See

Exiting the Program Mode

paragraph later in this section.

If a different Installer code is subsequently programmed, use it instead of 4112 to gain
access to the Programming mode.

When you enter the Program mode, data field

✱

20 is displayed (this is the first data field in

the system). The system now accepts entries for field

✱

20.

Programming a Data Field

1. Press

[

✱

]

. The display shows

Field ?

. Make the required entry (for example, 21).

2. When you have completely programmed a data field, the keypad beeps three times and

then automatically displays the next data field in sequence. To go to a different field, press
[

✱

] plus the desired field number.

3. If the number of digits that you need to enter in a data field is less than the maximum

digits available (for example, the phone number field), enter the desired data, then press
[

✱

] and the next data field number to be programmed.

4. If you try to enter a nonexistent field, the keypad doesn’t change and continues to display

Field ?

. Simply re-enter a valid field number.

Reviewing a Data Field/Erasing an Entry

Press

[#] + Field No.

. Data is displayed for that field number.

No changes are accepted

in this mode.

To delete an entry in a field,

press

[

✱

] + Field No. + [

✱

]

(

Applies only to fields

✱

40-

✱

44 and

✱

94.)

Interactive Mode Programming (

✱

56,

✱

58,

✱

80,

✱

81, and

✱

82)

Typical prompt displayed
during interactive mode
programming

Enter Zn Num.
(00 = Quit)

Press

[

✱

]

Interactive Mode Field No.

(for example,

✱

56). The

alpha keypad displays the first of a series of prompts requesting
entries.
A detailed procedure (with displays of prompts) is provided in
later sections of this manual.

Zone Number

Interactive Mode

Used to Program

✱

56 Zone Programming

Zone characteristics, report codes,
alpha descriptors, and serial numbers

✱

58 Expert Mode

Programming

Zone characteristics, report codes, and
serial numbers

✱

80 Relay Programming

4204 or 4229 Relay modules, or
Powerline Carrier devices

✱

81 Zone List

Programming

Zone Lists for relay/powerline carrier
and activation

✱

82 Alpha Programming

Zone alpha descriptors

Содержание Vista-20Bay











































































































































Результаты поиска

Содержание Vista-20Bay

Отзывы:

Похожие инструкции для Vista-20Bay

Бренды по названию

Популярные бренды

Bay Alarm Vista-20Bay, Инструкция по установке и настройке

Результаты поиска

Содержание Vista-20Bay

Отзывы:

Похожие инструкции для Vista-20Bay

Бренды по названию

Популярные бренды