manualshive.com logo in svg

Baxi EcoBlue 12 System ErP, Инструкция по установке и обслуживанию

Поделиться
Скачать
Baxi EcoBlue 12 System ErP Скачать руководство пользователя страница 38

38

EcoBlue System

7219708 - 01 (04/15)

6

Installation

6

Installation

6.1

General

1. 

Remove the sealing caps

from the boiler connections under

the bolier (including the condensate trap) before lifting into
position.

              A small amount of water may drain from the boiler once 
             the caps are removed. For ease of installation connect 
             and tighten the copper tails to the valves on the wall 
             jig BEFORE fitting the boiler !

2. Lift the boiler as indicated by the shaded areas. The boiler
should be lifted by TWO PEOPLE. Engage the mounting bracket
at the top rear of the boiler into the retaining lugs on the wall jig
using the aligning lugs for position (Fig.21) (see ‘Handling’
section 2.3.1).

3. 

Insert the sealing washers

between the valves and pipes on

the wall jig and the boiler connections. 

4. Tighten all the connections.

6.2

Assembly

6.2.1       Fitting the Pressure Relief Discharge Pipe

1. Remove the discharge pipe from the kit. 

2. Determine the routing of the discharge pipe in the vicinity of
the boiler. Make up as much of the pipework as is practical,
including the discharge pipe supplied.

             Note the intended position of the pipe is adjacent to the
             gas inlet pipe - see Section 3.2

             Make all soldered joints before connecting to the 
             pressure relief valve. Do not adjust the position of the 
             valve. The discharge pipe must be installed before 
             pressurising the system.

3. The pipework must be at least 15mm diameter and run
continuously downwards to a discharge point outside the
building. See section 5.2.9 for further details.

4. Utilising one of the sealing washers, connect the discharge
pipe to the adaptor and tighten the nut hand tight, plus 1/4 turn to
seal. 

5. Complete the discharge pipework and route it to the outside
discharge point.

Fig. 21

Remove Sealing Caps
from under the Boiler
before lifting into
position

Sealing
Washers (x 3)

Engage the Boiler Mounting

Bracket on the Boiler into the

Retaining Lugs using the

Aligning Lugs for position 

Fig. 22

Pressure Relief Valve

Discharge Pipe

Front Panel and Control
Box removed for clarity

Lift Here
Both Sides

Retaining
Lugs

When the Boiler Mounting Bracket on

the Boiler is in position on the

Retaining Lugs, the bottom polystyrene
may be discarded allowing the boiler to

swing into position 

Bottom
Polystyrene

Aligning
Lugs

Содержание EcoBlue 12 System ErP













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды