manualshive.com logo in svg

Baxi EcoBlue 12 System ErP, Инструкция по установке и обслуживанию

Поделиться
Скачать
Baxi EcoBlue 12 System ErP Скачать руководство пользователя страница 34

34

EcoBlue System

7219708 - 01 (04/15)

5

Before Installation

5.3.8          Horizontal Flue/Chimney Systems

1. The standard telescopic flue is suitable only for horizontal
termination applications.

2. All fittings should be fully engaged. The approximate
engagement is 40mm. Apply the lubricant supplied to the seal on
each fitting to aid assembly.   

3. Maximum permissible equivalent flue lengths are:-

             

(60/100)

(80/125)

Horizontal Concentric

10 metres

20 metres

4. Any additional “in line” bends in the flue system must be taken
into consideration. 
Their equivalent lengths are:-
Concentric Pipes:

           

135° bend

0.5 metres

           

93° bend

1.0 metres

             Flue length is measured from point (i) to (ii) as shown.  
             The elbow supplied with the standard horizontal 
             telescopic flue kit is not included in any equivalent 
             length calculations.

             Read this section in conjunction with the Flue

Installation Guide supplied with the boiler.

                  WARNING

                  

SUPPORT

- All flue systems MUST be securely 

                  supported at a MINIMUM of once every metre & 
                  every change of direction. It is recommended that 
                  every straight piece is supported irrespective of 
                  length. Additional supports are available as 
                  accessories.
                  

VOIDS

- Consideration must be given to flue systems

                  in voids and the provision of adequate access for 
                  subsequent periodic visual inspection.

Horizontal
Flues

(ii)

(i)

Plume Displacement Kit 60 /100 dia
1M Extensions 45° & 93° elbows are
also available - see the separate Flue
Guide.

NOTE:

Horizontal flue pipes should

always be installed with a fall of at least
1.5° from the terminal to allow
condensate to run back to the boiler.

(ii)

(i)

This bend is
equivalent to 1 metre

Total equivalent length =

A

+

B

+

C

+

2 x 90°     Bends

B

A

C

This bend is equivalent
to 1 metre

Содержание EcoBlue 12 System ErP













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды