manualshive.com logo in svg

Baxi EcoBlue 12 System ErP, Инструкция по установке и обслуживанию

Поделиться
Скачать
Baxi EcoBlue 12 System ErP Скачать руководство пользователя страница 20

20

EcoBlue System

7219708 - 01 (04/15)

4

Description of the Product

4.2

Operating Principle

4.2.1       Central Heating Mode 

1. With a demand for heating, the pump circulates water through
the primary circuit.

2. Once the burner ignites the fan speed controls the gas rate to
maintain the heating temperature measured by the temperature
sensor. 

3. When the flow temperature exceeds the setting temperature,
a 3 minute delay occurs before the burner relights automatically
(anti-cycling). The pump continues to run during this period.

4. When the demand is satisfied the burner is extinguished and
the pump continues to run for a period of 3 minutes (pump
overrun). 

4.2.2          Boiler Frost Protection Mode 

1. The frost protection mode is integral to the appliance and
functions as long as there is power to the boiler, as indicated by
the standby signal      .

2. With the boiler in ‘On’ mode and when the boiler temperature
falls below 5°C the boiler will fire until a temperature of 30°C is
reached. 

3. Further protection can be incorporated by using a system
frost thermostat.

4.2.3          Pump Protection

1. This activates once a week if there has been no demand. The
pump runs for 30 seconds to prevent sticking.

Boiler Schematic
Layout

             

To operate the boiler must be set so that the       symbol

is displayed. Press the               button to display the symbol.

N.B. If only         is displayed the boiler will not operate !

Key 
1. Pump with Automatic Air Vent 
2. CH System Pressure Gauge 
3. Central Heating Filter  
4. Non-return valve 
5. Hydraulic Pressure Sensor 
6. Boiler Drain Tap 
7. Pressure Relief Valve  
8. Condensate Trap
9. Gas Valve 
10. Safety Thermostat (105°C)  
11. Heating Flow Sensor 

12. Flue Sensor 
13. Boiler Adaptor 
14. Primary Heat Exchanger 
15. Spark Ignition Electrode 
16. Burner 
17. Flame Sensing Electrode 
18. Air/Gas Collector 
19. Heating Return Sensor 
20. Fan 
21. Air-Gas Venturi 
22. Expansion Vessel

Connections:-
A – Condensate Drain 
B – Heating Flow 
C – Gas Inlet  
D – Heating Return 

1

2

3

4

5

6

7

8

9

10

11

12

13

15

18

14

16

17

19

20

21

22

A

B

C

D

Содержание EcoBlue 12 System ErP













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды