manualshive.com logo in svg

Baxi Bermuda SP3, Руководство по установке и обслуживанию

Поделиться
Скачать
Baxi Bermuda SP3 Скачать руководство пользователя страница 39

Supplied By www.heating spares.co  Tel. 0161 620 6677

Support
Brackets
(401 Only)

Fire Support
Plate

Fire Support
Plate

Fire Support Plate - Bermuda 401 & 552

Fire Support Plate - Bermuda 45/3, 57/3, 45/4, 57/4 & 51/5

BERMUDA 45/3, 57/3, 45/4, 57/4 & 51/5

BERMUDA 401 & 552

If the fire is wall mounted remove and discard the existing
support frame (Bermuda 401 only). Retain the two
support brackets. These will be needed in wall mounting
the renewal fire.

If the fire is hearth mounted ensure that the base of the
builders opening and the front hearth are at the same
level.

Refer to "Site Requirements" (page 7) and prepare the
wall surface to the dimensions specified.

WALL FIXING

Two wall fixing plates are supplied in the Renewal Kit,
one for Bermuda 401/552 and one for Bermuda 45/3,
57/3, 45/4, 57/4 & 51/5.

BERMUDA 401 & 552

Take the fire support plate from the fire unit packaging
and loosely attach it beneath the boiler base protruding
from the fireplace opening using the M5 Nuts and screws
provided. Use the centre group of holes at each side.

NOTE:

If the fire is being used with a Bermuda 401 boiler

unit, the support brackets from the previous plate must be
fitted before the fire support plate can be fixed in place.

Push the support plate backwards until it touches the
surround or wall face and tighten the screws to lock it in
position.

BERMUDA 45/3, 57/3, 45/4, 57/4 & 51/5

Take the fire support plate from the fire unit packaging
and loosely attach it above the boiler base protruding
from the fireplace opening using the screws provided.
Use the slots at each side.

Push the support plate backwards until it touches the
surround or wall face and tighten the screws to lock it in
position.

WIRING

When connecting the firefront wire to the plug on the
boiler base tray refer to pages 8-12 of these instructions.

FIRE SUPPLY PIPE

Two fire supply pipes are supplied in the Renewal Kit, one
for Bermuda 401 & 552 and one for Bermuda 45/3, 57/3,
45/4, 57/4 & 51/5. The smaller (6mm) diameter one is for
Bermuda 45/3, 57/3, 45/4, 57/4 & 51/5 installations.

TO CONTINUE FITTING THE FIREFRONT REFER TO
THE INSTALLATION CHAPTER OF THESE
INSTRUCTIONS.

39

Bermuda 57/4 Illustrated

Содержание Bermuda SP3









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды