Baxi 946 Скачать руководство пользователя страница 1

Страница: 1 / 43

5115503/01

INSTALLER GUIDE

We trust that these instructions give sufficient details to enable this appliance to be

installed and maintained satisfactorily. However, if further information is required, our

Baxi Fires Division Technical Helpline

will be pleased to help.

Telephone

08706 061 065

(National call rates apply in the United Kingdom).

In the Republic of Ireland telephone

0044 8706 061 065.

INSTALLER: Please leave this guide with the owner

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

WHEN CONVERTED USING CONVERSION KIT NO. 0595231 THIS

APPLIANCE IS FOR USE WITH PROPANE GAS (G31).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Model 946

fitted with

Anthem, Aura 2, Blenheim, Camden,

Coast, Debut, Fusion,

Homeflame Traditional, Minima, Sonnet

Quantum

fascia.

INSET LIVE FUEL EFFECT GAS FIRE

(GC No. 32-032-63)

Содержание 946












































Результаты поиска

Содержание 946

Отзывы:

Похожие инструкции для 946

Бренды по названию

Популярные бренды

Baxi 946, Руководство по установке

Результаты поиска

Содержание 946

Отзывы:

Похожие инструкции для 946

Бренды по названию

Популярные бренды