Bavarian Soundwerks BMW E46 Скачать руководство пользователя страница 8

Страница: 8 / 13

Fold Down Seats Non Fold-Down Seats

Applying Sound Deadening to Enclosure

Your enclosure came with 4 sound deadening pieces which will need to be installed on the top of the

enclosure. Simply heat the sound deadening sheets using a heat gun or a hair dryer, and apply them as

shown. Be careful to not get the pieces too hot, as you can easily burn your hands.

Vehicles with Fold-Down Seats

First, open your trunk and locate the seat release latches. Remove the latch bolts with an 8mm nut driver.

Carefully pry the latch from its clips in the rear deck. This will reveal the front mounting holes for the new

D110 enclosure. Also, fold down the rear seats at this point.

8 of 13

Any reproduction, distribution, modification, or dissemination of these instructions without written permission from Bavarian Soundwerks is

expressly forbidden and a violation of international copyright law. Any violation will result in prosecution to the full extent available under the

law!

© Bavarian Soundwerks, LLC.

2195 Defoor Hills Rd., Suite D, Atlanta, GA 30318

P: 404.963.8857 |

www.bavsound.com

Содержание BMW E46













