Bavarian Soundwerks BMW E46 Скачать руководство пользователя страница 6

Again, it is important to remember here that we are essentially “T’ing” into the factory wires

. It is 

important that the factory signal flow be allowed to continue back into the factory amplifier.

This part of the installation is the most time consuming. Use the supplied blue butt connectors to make the 

connections. Make the connections at least 6” away from the factory amplifier plugs. After making the below 

connections, you can route the RCA Cables to the approximate amplifier location. 

1.

Carefully observe the factory amplifier harness. You will see a large bundle of wires going into the 

harness. The harness contains several wires, but don’t be overwhelmed. We will be using only four 

of them, and they are easy to locate. The wires will be twisted together, and each twisted pair 

represents a speaker or input. 

2.

You’ll need to isolate the following four (4) wires. They will be twisted together in pairs, as they 

enter the factory amplifier.

-Blue w/Black Stripe (+) twisted with Brown w/Orange Stripe(-)

-Yellow w/Black Stripe (+) twisted with Brown w/Orange Stripe (-)

3.

Now, orient yourself with the Line Output Converter that you received with your order. There are 

four individual wires coming out of the unit.

 If there are Brown wires on your LOC, disregard 

them. They will not be used.

Grey (+)                                             White (+)

Grey/Black (-)                                    White/Black(-)

With the audio input harness, left and right are irrelevant, so don’t worry about which pair goes 

where. Just make sure to reconnect the factory wires back together properly. 

     

                         Wire Color at LOC                                                 Wire Color at Factory Amplifier

Grey (+)

Blue w/Black Stripe

Grey/Black (-)

Brown w/Orange Stripe

White (+)

Yellow w/Black Stripe

White/Black (-)

Brown w/Orange Stripe

 

 

 

 

6  of 13

Any reproduction, distribution, modification, or dissemination of these instructions without written permission from Bavarian Soundwerks is 

expressly forbidden and a violation of international copyright law.  Any violation will result in prosecution to the full extent available under the 

law!

© Bavarian Soundwerks, LLC.

2195 Defoor Hills Rd., Suite D, Atlanta, GA 30318

P: 404.963.8857 | 

www.bavsound.com

 

Содержание BMW E46














Отзывы: