Bavarian Soundwerks BMW E46 Скачать руководство пользователя страница 10

Страница: 10 / 13

Models without Fold-Down Seats

It is easiest to have the trunk lining out at this point of the installation. You’ll be dropping two bolts

through the holes where the seat latches would be if your model had fold down rear seats, shown below

as the two “inner” bolt holes.

At this point it helps to have a friend here, but it’s not completely necessary. Have the quick-release

knobs handy (near your head) because while lying in the trunk, you’ll have the enclosure resting on

top of you. Insert the front brackets (Side with BSW logo) into the holes shown below:

Now push the enclosure towards the rear of the car (opening of the trunk) as far as you can, and lift the

rear (side closest to cabin of vehicle) of the enclosure up towards the rear deck,

making sure the bolts

10 of 13

Any reproduction, distribution, modification, or dissemination of these instructions without written permission from Bavarian Soundwerks is

expressly forbidden and a violation of international copyright law. Any violation will result in prosecution to the full extent available under the

law!

© Bavarian Soundwerks, LLC.

2195 Defoor Hills Rd., Suite D, Atlanta, GA 30318

P: 404.963.8857 |

www.bavsound.com

Содержание BMW E46













