Bavarian Soundwerks BMW E46 Скачать руководство пользователя страница 2

Страница: 2 / 13

Now, look to the floor of the trunk. You will see that the two plastic casings on either side

of the trunk are secured by plastic screws on the passenger side and fasteners on the

drivers’ side. The plastic screws on the passenger side can be removed using a flat head

screwdriver.

Remove these panels and place them aside. Keep all of the fasteners here so as not to

lose them.

Now, look to the carpeted drivers’ side of the trunk, and you will see two fasteners

securing the side panel. Remove these using your panel removal tool.

DO NOT Remove the two fasteners on either side of the rear of the carpeted panels

where the three panels seemingly come together. You

will

need to remove the large,

circular plastic insert in the center of the rear of the trunk however.

2 of 13

Any reproduction, distribution, modification, or dissemination of these instructions without written permission from Bavarian Soundwerks is

expressly forbidden and a violation of international copyright law. Any violation will result in prosecution to the full extent available under the

law!

© Bavarian Soundwerks, LLC.

2195 Defoor Hills Rd., Suite D, Atlanta, GA 30318

P: 404.963.8857 |

www.bavsound.com

Содержание BMW E46













