Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 54

Страница: 54 / 58

Bavarian RC Messerschmitt Me-410

54 -

Version Beta 1.0

Align the upper edge of the template with the upper edge of the fuselage skin and align the
aft crop mark with the rear corner of the canopy opening.

The fwd crop mark should align with the seam between the Fuselage skins 1 and 2.

Secure the template with tape.

Wrap the template around the fuselage. The bottom center line of the template should now
align with the center mark of the fuselage.

The fwd crop mark should line up with the seam between the Nose skin 2 and the Fuselage
skin 1.

The aft crop mark should line up with the seam between Fuselage skin 4 and the Tail skin.

Make the cut-out along the edge of the template. Make sure to adapt the angle of your blade
while you move along the the cut-out in oder to fit to the wing.

Repeat the same process on the RH side using the RH template.

Содержание Messerschmitt Me-410



























































Результаты поиска

Содержание Messerschmitt Me-410

Отзывы:

Bavarian RC Messerschmitt Me-410, Инструкции по сборке, Страница: 54 / 58

Результаты поиска

Содержание Messerschmitt Me-410

Отзывы: