Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 58

Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 18

Bavarian RC Messerschmitt Me-410

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use.

-

18 -

Version Beta 1.0

-

Dry fit the bottom part of Nose skin 1 and secure it with tape (don’t apply hot glue yet).

-

Use a box cutter to trim off the bottom edge of Nose skin 1.

Note: A prototype version of Nose skin 1 (without triangle part) is shown in these pictures

-

Leave the lower part of Nose skin 1 still secured with tape.

-

Now test fit the nose on the fuselage. Align the upper edge of Nose skin 1 with the access
frame and hold the nose in this position.

-

Check the bottom edge of Nose skin 1 to be flush with Fuselage skin 1.

-

If needed either trim off the Nose formers or glue a thin slice of foam to the Nose formers
(depending on the fit) to make the Nose skin 1 perfectly match Fuselage skin 1.

-

If everything fits, remove the tape and glue the Nose skin 1 to the Nose formers and the
bottom edge of Former A1.

Note: A prototype version of Nose skin 1 (without triangle part) is shown in these pictures

«
...
16
17
18
19
20
...
»

Содержание Messerschmitt Me-410



























































Отзывы:

Нет отзывов