Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 58

Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 16

Bavarian RC Messerschmitt Me-410

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use.

-

16 -

Version Beta 1.0

-

Remove the paper from one side of Fuselage skin 1.

-

Mold the skin to fit to the curvature of the fuselage. Make sure that the seam of Fuselage
skin 1 is on the top.

-

Fuselage skin 1 will overlap the access frame on the upper edge and Frames A2 on the fwd
edge. We’ll trim that after glueing.

-

Apply glue to the underside of the Former B and Formers A2 (lower) and attach the Fuselage
skin 1. Secure it with tape.

-

Apply glue to one side of Former B, Formers A2 (upper and lower) and the access frame and
attach Fuselage skin 1. Secure it with tape.

-

Repeat this step for the other side.

-

Trim off the overlap at the upper edge to make the Fuselage skin 1 flush with the access
frame.

-

Trim off the overlap at the Formers A2 to make the Fuselage skin 1 flush with Formers A2.

«
...
14
15
16
17
18
...
»

Содержание Messerschmitt Me-410



























































Отзывы:

Нет отзывов