Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 58

Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 25

Bavarian RC Messerschmitt Me-410

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use.

-

25 -

Version Beta 1.0

-

Apply more hot glue to the cavity all around the edges of the Hatch upper lock to properly
secure it. Make sure that you remove all excess glue.

-

Make a cavity in the upper part of Frame F2 for a magnet.

-

Test fit the magnet.

-

Apply a good beat of hot glue to the cavity and insert the magnet. Put a strip of tape over the
magnet and make sure that it is flush with the former. Leave the tape on.

-

Make a cavity in the Canopy former F for anther magnet.

-

Connect the magnets (with the tape in-between).

-

Apply a good beat of hot glue to the cavity of Canopy former F.

-

Insert the hook of the Hatch upper lock into the lower part, slide the canopy all the way back
and make sure that the magnet is properly located inside the cavity where you put the hot
glue.

-

Ensure that everything is properly aligned and hold the Canopy for at least 2 minutes to let
the glue full cool down.

-

Pull the canopy forward and remove it from the fuselage.

-

Remove the tape.

«
...
23
24
25
26
27
...
»

Содержание Messerschmitt Me-410



























































Отзывы:

Нет отзывов