manualshive.com logo in svg

Bavarian RC Messerschmitt Me-410, Инструкции по сборке, Страница: 19 / 58

Поделиться
Скачать
Bavarian RC Messerschmitt Me-410 Скачать руководство пользователя страница 19

Bavarian RC Messerschmitt Me-410 

 

 

 

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use. 

 

-

 

 19 - 

Version Beta 1.0

 

 

-

 

Take the Nose skin 2 RH and remove the paper from the inside. 

-

 

Mold the Nose skin 2 RH to fit to the curvature of the nose. 

-

 

Cut a bevel around the circumference of the Nose skin 2 RH (take care to have the correct 
angle). 

-

 

The Nose skin 2 RH has a bit of oversize along the edge towards Nose skin 1. Most of this can 
be trimmed off after glueing. 

-

 

Adjust the Nose skin 2 RH until you get a perfect fit. Make yourself small reference marks at 
the rear edge and at the nose tip to be sure that you always position the skin in the same 
way when adjusting and test fitting. 

-

 

This is a tricky process that will require some time. 

-

 

Also trim the Nose skin 2 RH at the edge towards the triangle part of Nose skin 1 to have a 
good fit. 

-

 

Then glue in place the Nose skin 2 RH starting from the top, but only glue the upper half in 
the first step. Secure it with tape. 

-

 

Then again check the fit of the remaining part and if everything is OK apply hot glue and 
attach it. Secure it with tape. 

 

 

 

 

 

Note: A prototype version of Nose skin 1 (without triangle part) is shown in these pictures 

 
 

 

Содержание Messerschmitt Me-410



























































Отзывы:

Нет отзывов