Baumer EAM MT Series Скачать руководство пользователя страница 17

Страница: 17 / 28

Baumer_EAM580_360_CANopen_MA_EN_Rev0003.0000h_Index0004.docx

Baumer Electric AG

06.08.2018

17/28

Frauenfeld, Switzerland

9.2

Redundant encoder

Figure 6: Dataflow of Error, Alarm, Warning, Diagnostic and Emergency messages (each node)

Error Behaviour

1029h-1h

Reset

Bit 0: Generic Position Alarm

Bit 12: Position Data not valid

Bit 0: Generic Error

Bit 4: Communication Error

CAN-Controller

Bus Passive

Bus Off

Bus Warning

Bus Active

RX Buffer Overflow

Error Behaviour

1029h-2h

Alarms 6503h

Error Register 1001h

Warnings 6505h

Bit 4: Battery charge low

Bit 0: Frequency exceeded

Bit 2: CPU Watchdog

Bit 3: Operating time limit

Bit 12: Mounting Error

Bit 13: Multiturn System

Bit 14: Singleturn System

Bit 15: Multiturn Supervision

Bit 3: Temperature

Bit 15: Battery empty

Only at
Startup

Error Behaviour

1029h-3h

Error Behaviour

1029h-1h

16-Bit Encoder Diagnostics 2117h

Bit 12: Communication Error

Bit 13: Temperature

Bit 15: Battery empty

Bit 14: Position Data not valid

Bit 3: Battery charge low

Bit 0: Frequency exceeded

Bit 1: CPU Watchdog

Bit 2: Operating time limit

Bit 4: Mounting Error

Bit 5: Multiturn System

Bit 6: Singleturn System

Bit 7: Multiturn Supervision

Bit 1: Commissioning diagnostic

Only at
Startup

Only at

Runtime

Only at

Runtime

Bit 11: Commissioning diagnostic

Bit 10: Generic Position Alarm

Emergency Message

Only at

Runtime

Multiturn Communication Monitor

Speed Monitoring

Reset Reason Watchdog

Battery Monitoring Warning

Temperature Montioring

Battery Monitoring Error

Multiturn Magnetic Field sequence

Singleturn Magnetic Field strength

Singleturn/Multiturn Supervision

CAN Node Guarding or Heartbeat

Non-Volatile Data Manager

Multiturn Power On Reset

Multiturn Magnetic Field strength

Only at
Startup

Only at

Runtime

9.3

Error behavior

The error behaviors are executed when the corresponding bit in object 1001 Error register is set and the device is in the
NMT-State Operational.

Example:
The error behavior 1029h-2 is set t

o “Change to Pre-Operational” (0). The device is in NMT state Operational

1. Generic error bit is set.

→ The device changes to Pre-Operational

2. The device is forced to NMT state Operational with NMT command Start

→ The device changes again to Pre-Operational if the generic error bit is not cleared.

Содержание EAM MT Series





























Результаты поиска

Содержание EAM MT Series

Отзывы:

Похожие инструкции для EAM MT Series

Бренды по названию

Популярные бренды

Baumer EAM MT Series, Руководство пользователя

Результаты поиска

Содержание EAM MT Series

Отзывы:

Похожие инструкции для EAM MT Series

Бренды по названию

Популярные бренды