background image

9

FIG. 13/A

5) GAS CONNECTION

The gas connection is located in the rear and on the
underside  of  the  appliance  118  mm  (for  60  cm),
165  mm  (for  70  cm),  255  mm  (for  90  cm)  from  the
right hand side.

There are two ways to carry out the connection to the
main gas line:
A. The hotplate can be connected with rigid pipe as
specified in AS/NZS 5601.
B. If  installing  with  a  hose  assembly,  install  with  a
hose  assembly  that  complies  with AS/ANZ  1869
(Australian  Certified),  10  mm  ID,  class  B  or  D,  no
more  than  1.2  m  long  and  in  accordance  with
AS/NZS 5601. Ensure that the hose does not contact
the hot surfaces of the hotplate, oven, dishwasher or
any other appliance that may be installed underneath
or  next  to  the  hotplate.  The  hose  should  not  be
subjected  to  abrasion,  kinking  or  permanent
deformation  and  should  be  able  to  be  inspected
along  its  entire  length  with  the  hotplate  in  the
installed position.
Unions  compatible  with  the  hose  fittings  must  be
used and all connections tested for gas leaks.
The gas supply connection point must be accessible
with the appliance installed.

Natural Gas

Natural Gas installations require the connection of a
gas  regulator  at  the  appliance.  This  regulator  is
supplied with the appliance on purchase.
Assemble  the  regulator  (noting  the  gas  flow
direction)  and  transition  pieces  (supplied  with  the
appliance), in accordance with figure 11.
The  transition  piece  on  the  supply  side  of  the
regulator must be provided by the installer.

Liquified Petroleum Gas

In  a  U-LPG  installation  the  gas  regulation  is  made
at  the  gas  cylinder  and  regulation  at  the  appliance
is  not  required. To  connect  supply  to  the  appliance
use 

transition 

pieces 

as 

shown 

in 

figure  12.  These  pieces  are  supplied  with  the
appliance on purchase.

WARNING:
THE  BURNER  FLAME  MUST  BE ADJUSTED  BY
THE INSTALLER.
FAULTY  INSTALLATION  WILL  NOT  BE
COVERED UNDER WARRANTY.
THE APPLIANCE IS FACTORY SET FOR NATURAL
GAS.  THE  TEST  POINT  PRESSURE  SHOULD  BE
ADJUSTED  TO  1.00kPa  WITH  THE  WOK  BURNER
OPERATING AT MAXIMUM.

INSTALLATION

FIG. 11

FIG. 12

FIG. 13/B

220-240 V~

220-240 V~

Содержание B6FS

















Отзывы: