background image

1) BURNERS

A diagram is screen-printed above each knob on the
front  panel.  This  diagram  indicates  to  which  burner
the  knob  in  question  corresponds. After  having
opened  the  gas  mains  or  gas  bottle  tap,  light  the
burners as described below:

- manual ignition

Push  and  turn  the  knob  corresponding  to  the
required  burner  in  an  anticlockwise  direction  until  it
reaches the full on position (large flame fig. 1), then
place a lighted match near the burner.

- Automatic electrical ignition

Push  and  turn  the  knob  corresponding  to  the
required  burner  in  an  anticlockwise  direction  until  it
reaches the full on position (large flame fig. 1), then
depress the knob.

- Lighting  burners  equipped  with  flame  failure

device

The  knobs  of  burners  equipped  with  flame  failure
device must be turned in an anticlockwise direction
until  they  reach  the  full  on  position  (large  flame
fig. 1) and come to a stop. Now depress the knob in
question  and  repeat  the  previously  indicated
operations.
Keep  the  knob  depressed  for  about  10  seconds
once the burner has ignited.

Note:  you  are  advised  not  to  try  and  light  a
burner  if  the  flame  divider  (Burner  Cap)  is  not
correctly placed.

HOW TO USE THE BURNERS

Bear  in  mind  the  following  indications  in  order  to
achieve maximum efficiency with the least possible

gas consumption:

- use  adequate  pans  for  each  burner  (consult  the

following table and fig. 2).

- When the pan comes to the boil, set the knob to the

reduced rate position (small flame fig. 1).

- Always place a lid on the pans.
- Use only pan with a flat bottom and in thick metal.

Burners

Power ratings

Pan Ø in cm

NATURAL  ULPG 

Ultra rapid

13.5 MJ/h

11.4 MJ/h

22 ÷ 24

Rapid

12.0 MJ/h 10.4 MJ/h

20 ÷ 22

Semi

 

rapid

7.1 MJ/h

6.3 MJ/h

16 ÷ 18 

Auxiliary

4.1 MJ/h

3.6 MJ/h

10 ÷ 14

- Burners  with  flame  failure  device  may  only  be

ignited  when  the  relative  knob  has  been  set  to

the Full on position (large flame fig. 1).

- Matches  can  be  used  to  ignite  the  burners  in  a

blackout situation.

- Never leave the appliance unattended when the

burners are being used. Make sure there are no

children  in  the  near  vicinity.  Particularly  make

sure  that  the  pan  handles  are  correctly

positioned and keep a check on foods requiring

oil and grease to cook since these products can

easily catch fire.

- The  appliance  must  not  be  used  by  people

(including  children)  with  impaired  mental  or

physical  capacities,  or  without  experience  of

using  electrical  devices,  unless  supervised  or

instructed  by  an  expert  adult  responsible  for

their  care  and  safety.  Children  should  not  be

allowed to play with the equipment.

- DO NOT SPRAY AEROSOLS IN THE VICINITY OF

THIS APPLIANCE WHILE IT IS IN OPERATION.

- Should a crack appear on the surface of the glass,

disconnect the appliance from the electricity supply

immediately.

- Do not place pans with an unstable or deformed

bottom on the burner, as these may tip or spill their

contents, causing accidents.

- DO  NOT  USE  OR  STORE  FLAMMABLE

MATERIALS NEAR THIS APPLIANCE.

- Do not use the hob as a work surface.
- This  product  is  not  to  be  installed  in  marine

crafts, caravans, or mobile homes.

- Containers    wider    than    the    unit    are  not

recommended.

- Avoid  scraping  the  pans  on  the  glass  surface,

as the surface may become scratched.

- DO NOT MODIFY THIS APPLIANCE.

- DO NOT USE AS A SPACE HEATER.

USE

FIG. 1

FIG. 2

In the event of the Burner flames being accidentally
extinguished, turn off the burner control and do not
attempt to re-ignite the burner for a least 1 minute.

4

Содержание B6FS

















Отзывы: