Bartec PETRODAT 3003 Скачать руководство пользователя страница 34

Страница: 34 / 76

Delivery mode
32

Aircraft Refuelling, Operating Instructions, BA 090323, (07.03.2022)

4.8

Performing the refuelling

Refuel the aircraft in accordance with the regulations in force. During delivery, the following data is
shown on the display:

Flight
number

Fuel type and quantity

See section 5.1.7

Parking
position

Aircraft registration

Weight

Flow rate

Display of the differential
pressure, which has been
extrapolated to 100%

Total meter quantity

Water content

if a water sensor is installed

Display of additional
delivery information

Current tank content

if a dipstick is installed

Delivered quantity

Product temperature

AVG or ACT

AVG =

The displayed

temperature refers to the

average temperature

ACT =

The displayed

temperature refers to the

current product

temperature.)

Vt or V15

Vt =

The displayed quantity

refers to the current

product temperature

V15 =

The displayed quantity

refers to 15 °C

(compensated delivery))

4.8.1 Further information

Use the selection buttons to call up more detailed information.

Designation

Description

Quantity u/k

Quantity, uncompensated and compensated

Temperature a/m

Temperature, current and averaged

Density conf./office

Density and temperature is configured on the vehicle and has been received
by the office

Diff. pressure a/100% Differential pressure, current and extrapolated to 100% flow
FWS a/m

Water content, current and averaged

Dipstick

Tank content

Содержание PETRODAT 3003













































































Результаты поиска

Содержание PETRODAT 3003

Отзывы:

Похожие инструкции для PETRODAT 3003

Бренды по названию

Популярные бренды

Bartec PETRODAT 3003, Руководство по эксплуатации

Результаты поиска

Содержание PETRODAT 3003

Отзывы:

Похожие инструкции для PETRODAT 3003

Бренды по названию

Популярные бренды