Barco R9001440 Скачать руководство пользователя

Страница: 6 / 34

R9001440/9

GRAPHICS

Panel Adjustments

Date:10/02/2000

6300

Panel Adjustments

Connection of the TCR

tracker unit

Install the TCR Tracker unit, as illustrated in

drawing below. Make sure that the switch on

the TCR Interface is put in the position OFF

and that the projector is switched to Standby.

TCR Tracker

Detailed view of the TCR Tracker

and interface, see next page

TCR Interface

Screen

Projector

from Sensor

to RS232 IN

projector

to COMM PORT

projector

Change Projector Address

Every projector requires an individual address

between 0 and 255. This address can be

software installed.

To change that address:

Push the cursor key

to highlight

'Change Projector Address''.

Press

ENTER

to display the

Change

Projector Address

menu. The actual

address will be filled in.

Select with or

then <ENTER>

<EXIT> to return.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTIME HISTORY

DIMMING

MORE ...

CHANGE PROJ. ADDRESS

Enter new address

001

Select with or

Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTIME HISTORY

DIMMING

MORE...

Select with or

then <ENTER>

<EXIT> to return.

Change Baudrate PC

The communication speed between projector

and computer, e.g. PC or MAC, has 8 possible

speeds. The baud rate speed can be software

set. Handle as follow:

1 Push the cursor key

to highlight

'Change Baudrate PC''.

2 Press

ENTER

to display the

Change

Baudrate PC

menu. The actual baudrate

will be highligted.

The following baud rates are available :

230400/115200/57600/38400/19200/9600/

4800/1200

3 Push the cursor key

to highlight the

baudrate 9600 and press

ENTER

to select.

Select with or

<ENTER> to accept

<EXIT> to return.

CHANGE BAUDRATE PC

230400
115200

57600
38400
19200

9600

4800
1200

Set the projector address on 001 as follows:

The first digit is highlighted. Enter the new projector address with :

- the digit keys on the RCU or the local keypad or

- push the cursor key

to select a digit and change the value by pushing

the cursor key

until the new value is reached. Continue with the other

digits on the same way.

Содержание R9001440



































Результаты поиска

Содержание R9001440

Отзывы:

Похожие инструкции для R9001440

Бренды по названию

Популярные бренды

Barco R9001440, Руководство по настройке

Результаты поиска

Содержание R9001440

Отзывы:

Похожие инструкции для R9001440

Бренды по названию

Популярные бренды