![background image](http://html1.mh-extra.com/html/barco/iex-series/iex-series_installation-and-user-manual_3851379012.webp)
R5915190 /01
IEX series
12
•
It is not allowed to climb or hang any additional equipment on the back of an IEX wall. Nothing is to be
allowed to hang from the cables of an IEX tile.
•
Any failures must be immediately and appropriately dealt with (equipment returned to Barco). Failing
equipment cannot be left to run in a wall.
•
No additional tools (hammers, pry-bars, etc.) are to be used to force handles or locks into place. All moving
parts should be managed by hand.
•
Only Barco cables specified to be used with the IEX display are to be used to connect components in the
IEX wall. Further, care must be taken to connect signal only according to the installation manual.
•
IEX tiles are not to be used in the vicinity of any equipment that is not CE and UL/ETL certified.
•
When reconnecting components in an IEX tile, care must be taken to ensure that cables are carefully
routed according to the installation manual to prevent damage to the cables or other parts of the IEX tile.
•
IEX tiles can be cleaned only in accordance to the procedures defined in the installation manual.
•
The IEX display is an indoor product. Use the IEX tiles only in a dry area away from direct sunlight, dust
and moisture. Never install and use the IEX tiles in an outdoor environment.
•
Ensure rigging hardware is able to handle the weight of the entire IEX with appropriate safety factors.
•
Ensure good ventilation for the LED display when designing the heat dissipation solution.
•
Switch off the power immediately and contact the professional personnel when the LED display has any
abnormal conditions such as peculiar smell, smoke, electric leakage, and abnormal temperature.
•
In case the LED display is not been powered on twice a per week for at least 2 hours each time then the
“
Warm up procedure
”
as described in Chapter 5.4 has to be followed precisely.
•
Installing the LED display in the following places may result in an equipment failure and reduce its lifespan:
near the sea, in an area with salt and alkali or sulphurous gases, near a kitchen exhaust position, or at a
place where the difference between indoor and outdoor temperatures is great. Consult our professional
personnel at the service center if the LED display must be installed in any of these places.
1.5 LED Display Humidity precautions
Overview
LED displays have recommended temperature and humidity ranges for storage and operation. Use of the
products in temperature or humidity ranges outside these recommendations can cause temporary or
permanent damages.
The SMD LEDs used on indoor LED displays are moisture sensitive components, the smaller the size of the
LEDs, the more sensitive the LEDs are for humidity due to their structure and electric clearance, specifically a
chip LED (used for pixel pitches of sub 2mm) is highly sensitive.
When the humidity is high, it might cause condensation on and in the LED. Condensation on the LED is
dangerous and can cause short-circuits, dead LEDs and other issues.
Therefore, customers should strictly follow the humidity precautions and start up procedure when using the
screen.
Содержание IEX Series
