32
MAINTENANCE
GREASE FILTERS
The metallic grease filters are positioned on the bottom of the hood and are used to
contain any grease which is normally emitted in cooking fumes, thereby impeding the
deterioration of the motor.They can be washed either by hand or in the dish washer.
For washing by hand, use hot water and soap; this can be done by hand brushing
vigorously several times and then rinsing under the tap.
After washing, the grease filters should be dried and re-fitted correctly.
It is possible that after washing the filter will have slight change in the colour.
It is advised to wash the grease filters after circa 50-100 hours of use of the
cooking top.
If the grease filters are very dirty, the motor can only take in a small quantity of air,
and performance is reduced;
The grease which accumulates on dirty filters is easily inflammable and
can cause fires,
if they are not removed by periodic washes.
The manufacturer declines any responsibility for fires caused by poor maintenance of
the grease filters.
CARBON FILTERS
The carbon filters at the suction outlet of the motor, are used to retain the odours of the
kitchen fumes. It is not necessary to use carbon filters.
The use of carbon filters is necessary if you use the hood as filtering.
There are 2 kinds of carbon filters, carbon filters that can be regenerated and carbon
filters that cannot be regenerated.
Carbon filters that can be regenerated:
Please follow and read the instructions given with the carbon filters that can be
regenerated as far as mounting and re generation are concerned.
Carbon filters that cannot be regenerated:
we advise to replace the carbon filters after circa 200-300 hours of use of the
cooking top. The carbon filters that cannot be regenerated cannot be either washed
nor regenerated but need to be replaced when expired.
Carbon Filters do not guarantee the interchange of oxygen in the air.
To ensure correct ventilation and air interchange in the kitchen, national and
international regulations exist, which should be respected.
The manufacturer denies any responsibility for fires caused by failure to replace the
carbon filters.
REPLACEMENT OF LAMPS
Always replace the lamps with lamps which have the same electrical characteristics
(see TECHNICAL DATA). Before replacing the lamps, make sure that they are cold and
that power has been completely turned off.
Please follow the sequenze as shown in L series pictures.
Reconnect to electricity.
If te lights are not working, check that the lamps are correctly fit.
Содержание B_AMBIENT
