background image

                            

 Installation & Operating Instructions

 

 |  

Baracuda XA Robotic Pool Cleaner

        

27

CONTROL UNIT STATUS

POSSIBLE CAUSES

SOLUTIONS

THE 

LED IS OFF

Weak W-Fi signal

•  Install the iAquaLink™ app, using a smartphone or 

tablet.  Check the strength of the wireless network 

signal on the mobile device by checking the status 

of the control box connection. If the Wi-Fi network 

is weak, install a Wi-Fi extender. 

•  Use an app dedicated to analysing the Wi-Fi con-

nection: several are available in iOS or Android. 

The 

LED is lit but 

the Wi-Fi  connection is 

non-existent (or spotty).  
The “Connection Error” 

message is displayed  

on  the screen in the  

iAquaLink™ app. 

The control box is too far 

from the home Wi-Fi router

•  On initial set-up, place the cleaner’s control box as 

close as possible to the home Wi-Fi router.  

Do not use an electrical extension (See section on 

“Electricity supply connection”), then repeat the 

configuration steps (See section on “First-time 

cleaner  configuration”): 

•  Once the 

LED lights up, plug in the control box 

near the pool.  

•  If the 

LED does not light up, plug in the control 

box again as close to the house as possible. 

•  If the 

LED still does not light up, install a Wi-Fi 

extender.

The 

LED is lit and  

the  “PROG” message  

is displayed (depending  

on the model).  

A message is displayed 

in the app. 

A software update is in  

progress. 

•  Wait for the update to complete. 
•  Do not disconnect the power cable from the 

cleaner during  an update.

The buttons can’t be 

activated. 

The 

LED is still not lit 

during this operation.

There may be several reasons for a weak Wi-Fi signal 

- The distance between the router and the cleaner’s control unit, 

- The type of router, 

- The number of walls separating the router from the cleaner’s control unit, 

- The Internet service provider, etc...

Recycling

 

Your appliance must not be thrown into a normal bin. It will be selectively collected for the purpose of reuse, recycling, or  
transformation. If it contains any substances that may be harmful to the environment, these will be eliminated or neutralised.  
Contact your retailer for recycling information.  

Содержание xa2030































Отзывы: