baracuda xa2030 Скачать руководство пользователя страница 26

Страница: 26 / 30

Baracuda XA Robotic Pool Cleaner

| Installation & Operating Instructions

Using the Control Unit:

After following the troubleshooting solutions, press any key to delete
the error code (except the

button).

From the iAquaLink™ app:

After following the troubleshooting solutions, press

Clear Error

DELETING AN ERROR CODE

APPLIANCE BEHAVIOUR

CONTROL UNIT STATUS

POSSIBLE CAUSES

SOLUTIONS

THE

LED IS

FLASHING

The version of the app

used is obsolete

• Update the app version.

ALL LED LIGHTS

ARE OFF

The control box is connected

to the router but not to the

cloud server (LAN connected,

WEB not connected)

• Contact your Internet service provider.
• Disconnect the home Wi-Fi router for 10 seconds.

Re connect it and see whether the LEDs come

back on.

• Check the internet connection - the network may

be down.

Incompatible 5GHz router

• Replace the router.

Very high luminosity

• Cover the appliance to protect it from the sun’s

rays and check that the light indicators turn on.

Control unit disconnected

• Connect the control unit.

(See section on “Electricity Supply Connection”).

Power cut

• Check that there is power to the circuit breaker
• Check that there is power to the socket by

connecting another appliance to it.

Internet connection lost

• Check the internet connection - the network may

be down.

THE

LED IS OFF

Internet connection lost

• Check the internet connection - the network may

be down.

• Ensure that you have a sufficiently strong

Wi-Fi signal.

There are several ways to check the

strength of the Wi-Fi signal:

• Unplug the home Wi-Fi router, then plug it back in.
• Using a laptop, go into Configuration Panel to see

the status of your network connections.

• Check the strength of the wireless network signal

on the laptop by checking the status of the control

box connection.

Содержание xa2030































Результаты поиска

Содержание xa2030

Отзывы:

Похожие инструкции для xa2030

Бренды по названию

Популярные бренды

baracuda xa2030, Инструкция по установке и эксплуатации

Результаты поиска

Содержание xa2030

Отзывы:

Похожие инструкции для xa2030

Бренды по названию

Популярные бренды