manualshive.com logo in svg

Banner Sure Cross DXM1200-Bx, Инструкция по эксплуатации, Страница: 41 / 62

Поделиться
Скачать
Banner Sure Cross DXM1200-Bx Скачать руководство пользователя страница 41

7.4.2 Calculating the Communications Timeout for Battery-Powered
MultiHop Radios

Battery-powered MultiHop radios are configured to run efficiently to maximize battery life. By optimizing battery life, the

allowed communications window for receive messages is slow (once per 1.3 seconds) and sending message rates are

standard (once per 0.04 seconds).
A MultiHop device is set from the factory with the retry parameter of 8. This means that under worst-case conditions, a

message is sent from the DXM1200 to an end device a total of nine times (one initial message and eight retry messages).

The end device sends the acknowledgment message back to the DXM1200 a maximum of nine times (one initial message

and eight retries). A single Modbus transaction may send up to two me 16 retry messages before the transaction is

complete. In addition, the radios randomly wait up to one time period before retransmitting a retry message. So to allow for

the random wait time, add one extra time period for each in-between time of retries.
To calculate the communication timeout parameter for a Master radio to a slave radio (no repeaters):

Master to Slave Send time = (9 × 1.3 sec) + (8 retry wait × 1.3 sec) = 22 seconds
Slave to Master Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Total Send/Receive time = 23 seconds
Minimum Timeout period = 23 seconds

If the link quality of the network is poor, the maximum transfer times may happen. Set the timeout parameter to

accommodate the maximum number of retries that may happen in your application.
When MultiHop repeaters are added into the wireless network, each additional level of hierarchical network increases the

required timeout period. Since MultiHop repeaters are running at the highest communications rate, the overall affect is not

as great.

Master to Repeater Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Repeater to Master Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Additional Timeout period for a repeater = 2 seconds

Using the timeout calculation above of 23 seconds, if a repeater is added to the network the timeout should be set to 25

seconds. For each additional MultiHop repeater device creating another level of network hierarchy, add an additional two

seconds to the timeout period.

7.4.3 Calculating the Communication Timeout for 10–30 VDC
MultiHop Radios

Line-powered (10–30 V dc) MultiHop devices operate at the maximum communication rate, resulting in a much lower

timeout parameter setting. For each repeater added to the network, increase the timeout parameter 2 seconds.
For a Master radio to a 10–30 V dc powered slave radio (no repeaters):

Master to Slave Send time = (9 × 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Slave to Master Send time = (9 ×* 0.04 sec) + (8 retry wait × 0.04 sec) = 1 second
Total Send/Receive time = 2 seconds
Minimum Timeout period = 2 seconds

7.4.4 Adjusting the Receive Slots and Retry Count Parameters

The number of receive slots governs how often a MultiHop device can communicate on the wireless network.
Battery-powered devices typically have DIP switches that allow the user to set the number of receive slots, which directly

affects the battery life of the radio. Adjusting the receive slots changes how often a message can be received. By default,

the receive slots are set to 4 (every 1.3 seconds). When the receive slots are set to 32, the radio listens for an incoming

message every 0.16 seconds.
Users may also leave the retry mechanism to the application that is accessing the wireless network, in this case the

DXM1200. Adjust the number of retries in the MultiHop devices by writing the number of retries desired to Modbus register

6012. The factory default setting is 8.

 

 

Sure Cross

®

 DXM1200-Bx Wireless Controller

 

www.bannerengineering.com - Tel: + 1 888 373 6767

41

Содержание Sure Cross DXM1200-Bx































































Отзывы:

Нет отзывов