banks iDash 1.8 Скачать руководство пользователя страница 8

Страница: 8 / 76

97654 v.7

DISCLAIMER OF LIABILITY &

WARRANTY,

CONTINUED

THIS PRODUCT. THIS WARRANTY GIVES

YOU SPECIFIC RIGHTS. YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

LOCALITY TO LOCALITY AND CERTAIN

LIMITATIONS CONTAINED IN THIS

WARRANTY MAY NOT APPLY TO YOU.

If any part of this limited warranty is

held to be invalid or unenforceable, the

remainder of the limited warranty shall

nonetheless remain in full force and

effect. This limited warranty is governed

by the laws of the State of California,

without reference to its conflict of law

provisions.

SAFETY INFORMATION

DO NOT USE the iDash NEAR WATER

OR IN AN ELECTRICAL STORM AS

THIS COULD LEAD TO AN ELECTRICAL

SHOCK. DO NOT USE the iDash NEAR A

NATURAL GAS LEAK.
Check local regulations for disposal of

electronic products.

COPYRIGHT INFORMATION

Products and corporate names

appearing in this manual are for

identification purposes only. These

names may or may not be registered

trademarks or copyrights owned by

these corporations. Their use by Gale

Banks Engineering is for the express

purpose of identification or explanation

for the owner’s benefit and is in no way

meant to infringe.

DISCLAIMER

Banks Engineering reserves the right

to make improvements, changes or

updates to its software at any time

without notice. As such the illustrations,

images, and descriptions used in this

manual may not match exactly the

referenced screens as they appear in

the latest release of the application.

Содержание iDash 1.8













































































Результаты поиска

Содержание iDash 1.8

Отзывы:

Бренды по названию

Популярные бренды

banks iDash 1.8, Руководство пользователя

Результаты поиска

Содержание iDash 1.8

Отзывы:

Бренды по названию

Популярные бренды