B&R Industries Panel PC 2100 Скачать руководство пользователя страница 185

Страница: 185 / 191

Table index

Panel PC 2100 swing arm user's manual V1.00

185

Table 110:

Boot - Boot device priority........................................................................................................ 128

Table 111:

Boot - Boot configuration.......................................................................................................... 129

Table 112:

Exit.............................................................................................................................................131

Table 113:

RAM address assignments....................................................................................................... 132

Table 114:

I/O address assignments.......................................................................................................... 132

Table 115:

IRQ interrupt assignments in PIC mode...................................................................................132

Table 116:

IRQ interrupt assignments in APIC mode................................................................................ 133

Table 117:

5SWWI8.0343-MUL, 5SWWI8.0443-MUL - Order data............................................................134

Table 118:

Device functions in Windows Embedded 8.1 Industry Pro.......................................................134

Table 119:

5SWWI7.1300-MUL, 5SWWI7.1400-MUL - Order data............................................................137

Table 120:

Windows 7 - Overview..............................................................................................................137

Table 121:

5SWWI7.1543-ENG, 5SWWI7.1643-ENG, 5SWWI7.1743-MUL, 5SWWI7.1843-MUL - Order da-

ta................................................................................................................................................139

Table 122:

Device functions in Windows Embedded Standard 7...............................................................139

Table 123:

0TG1000.01, 1TG4600.10-5, 1TG4601.06-5 - Order data....................................................... 141

Table 124:

MIFARE commands - Authentication key storage....................................................................152

Table 125:

MIFARE access rights (parameter 2)....................................................................................... 153

Table 126:

MIFARE access rights (5-byte parameters)..............................................................................153

Table 127:

MIFARE access rights - Parameters 2, 3 and 4 (data blocks)................................................. 153

Table 128:

MIFARE access rights - Parameter 5 (sector trailer)................................................................153

Table 129:

General commands................................................................................................................... 153

Table 130:

Update commands.................................................................................................................... 154

Table 131:

MIFARE commands.................................................................................................................. 154

Table 132:

General commands................................................................................................................... 156

Table 133:

Update commands.................................................................................................................... 156

Table 134:

ISO 15693 commands.............................................................................................................. 156

Table 135:

Operating errors........................................................................................................................ 158

Table 136:

RFID stack high byte error messages...................................................................................... 158

Table 137:

RFID stack low byte error messages....................................................................................... 159

Table 138:

0TB103.9, 0TB103.91 - Order data.......................................................................................... 164

Table 139:

0TB103.9, 0TB103.91 - Technical data....................................................................................164

Table 140:

0TB1210.3100 - Order data......................................................................................................166

Table 141:

0TB1210.3100 - Technical data................................................................................................166

Table 142:

5MMUSB.2048-01, 5MMUSB.4096-01 - Order data................................................................ 167

Table 143:

5MMUSB.2048-01, 5MMUSB.4096-01 - Technical data.......................................................... 167

Table 144:

Abbreviations in this user's manual.......................................................................................... 171

Table 145:

RFID read/write transponder unit..............................................................................................176

Table 146:

Pushbutton /2300...................................................................................................................... 176

Table 147:

Pushbutton /2500...................................................................................................................... 176

Table 148:

Selector switch 1.30.272.102/2200........................................................................................... 176

Table 149:

Key switch 1.30.255.222/0000..................................................................................................177

Table 150:

E-stop 1.30.273.502/0300......................................................................................................... 177

Table 151:

Switching element 1.20.126.005/0000...................................................................................... 177

Table 152:

Switching element 1.20.126.414/0000...................................................................................... 178

Table 153:

5-wire AMT touch screen - Technical data...............................................................................179

Table 154:

3M touch screen - Technical data............................................................................................ 180

Содержание Panel PC 2100
































































































































































































Результаты поиска

Содержание Panel PC 2100

Отзывы:

Похожие инструкции для Panel PC 2100

Бренды по названию

Популярные бренды

B&R Industries Panel PC 2100, Руководство пользователя

Результаты поиска

Содержание Panel PC 2100

Отзывы:

Похожие инструкции для Panel PC 2100

Бренды по названию

Популярные бренды