Bandit 2550 Скачать руководство пользователя страница 58

Страница: 58 / 98

Bandit

MODELS 2550/2550T

TROUBLESHOOTING

MAINTENANCE

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine will

not start. (See

Engine Mfg.

manual for further

information).

Loose ground cable.

Clean and tighten.

Loose hot cable.

Clean and tighten.

Dead battery.

Recharge or replace.

Cutter wheel was engaged before the

machine was started.

Make sure the ignition switch is off,

disengage cutter wheel, and then

restart the machine.

Batteries in remote are dead.

Replace.

Emergency stop activated.

Pull or twist the emergency stop to

deactivate.

Cutter wheel

vibration.

Tooth missing.

Replace missing teeth.

Pocket out of balance.

Do not mix new and worn teeth.

Always replace pockets in pairs across

from each other.

Improper tooth arrangement.

Do not mix new and worn teeth.

Install correctly with like pairs of teeth

directly across from each other.

Cutter wheel

throwing teeth.

Bad pocket.

Replace pocket.

Dirt in pocket.

Clean pocket and replace teeth.

Always replace pockets in pairs

across from each other.

Breaking teeth.

Operator hitting rocks.

Avoid rocks, stones, etc.

Cutter wheel stops

turning.

Bad hydrostatic motor.

Replace.

Bad hydrostatic pump.

Replace.

Engagement cable loose or broke.

Adjust or replace.

Low hydraulic pressure.

Reset pressure.

Debris wedged around cutter wheel.

Clean out debris.

Bearing will not

take grease.

Grease fitting clogged.

Replace.

Machine will not

respond to remote.

Weak or dead batteries.

Replace

Remote not turned on before starting

the machine engine.

Turn off engine, turn remote power on

and then restart the machine.

Machine is out of range of the remote.

Move closer and make sure there are

not obstructions between the operator

and the machine.

Broken or damaged antenna.

Replace.

Remote power switch is turned off.

Shut down and restart the machine.

Содержание 2550



































































































Результаты поиска

Содержание 2550

Отзывы:

Похожие инструкции для 2550

Бренды по названию

Популярные бренды

Bandit 2550, Руководство по эксплуатации

Результаты поиска

Содержание 2550

Отзывы:

Похожие инструкции для 2550

Бренды по названию

Популярные бренды