Bandit 2550, Руководство по эксплуатации

Страница: 12 / 98

Bandit
8
Copyright 4/21
MODELS 2550/2550T SAFETY PROCEDURES
SAFETY PROCEDURES
It is very important after you have operated a new
machine for approximately an hour to shut down the
machine and recheck all nuts and bolts. It is normal
for nuts and bolts to loosen once on a new piece of
machinery. If you tighten them now, there is a good
possibility they won’t loosen again. Certain nuts and
bolts should be checked periodically such as cutter
teeth bolts, etc. for torque and fi t.
Most of the nuts used on the Bandit Grinder are
self locking. After a nut or bolt has been removed
fi ve times, it should be replaced to ensure proper
tightness. This is especially critical on the cutter tooth
bolts!
After the engine is started, let the grinder wheel
turn at the lowest RPM’s possible. Listen for any type
of noise that is foreign. Any steel on steel noise is
foreign. If you hear a noise, stop the engine, fi nd the
problem and fi x it.
It is very important after you have operated a new
machine for approximately an hour to shut down the
machine and recheck all hydraulic fi ttings. Relieve
all pressures and retighten as needed.
DO NOT GO NEAR HYDRAULIC LEAKS! High
pressure oil easily punctures skin causing serious
injury, gangrene, or death. Avoid burns from fl uid.
Hot fl uid under pressure can cause severe burns.
DO NOT use fi ngers or skin to check for leaks. Lower
load or relieve hydraulic pressure before loosening
fi ttings. Relieve all pressure in the system before
disconnecting the lines, hoses, or performing other
work. Use a piece of cardboard to fi nd leaks. Never
use your bare hands. Allow system to cool down to
ambient temperature before opening any coolant or
hydraulic oil system.
In cold weather situations let your hydraulic
system idle for approximately 15 minutes to allow
the system to warm up to operating temperature.
WARNING
!
WARNING
!
Keep the machine in good condition. Be sure the
machine is in good operating condition and that all
safety devices, including guards and shields are
installed and functioning properly. Visually inspect
the machine daily before starting the machine. Refer
to the “Daily Start Up & Maintenance”. Make no
modifi cations to your equipment unless specifi cally
recommended or requested by Bandit Industries Inc.
DANGER
!
DO NOT operate this machine unless all hydraulic
control devices operate properly. They must function,
shift and position smoothly and accurately at all
times. Faulty controls can cause personal injury!
WARNING
!
Before attempting any type of maintenance,
disengage clutch or cutter wheel engagement, wait
for the cutter wheel to come to a complete stop,
position and lock the cutter wheel arm in the transport
position, turn off engine, remove the ignition key,
make sure the ignition key is in your possession,
install the cutter wheel lock pin, wait 2 minutes then
disconnect the battery.
ALWAYS install the lock pin into the cutter lock
tube before working on the grinder.
Simply slide the lock pin into the cutter wheel lock
tube. This is to ensure that the cutter wheel cannot
be started while you are working on the grinder. If
for some reason the cutter wheel would start to turn,
it would simply hit the lock pin.
Never use jumper cables during freezing
temperatures. Tow the machine inside and allow
the battery time to warm up. If the machine must
be started outside, inspect the battery acid for ice
formation. Explosion will occur with a frozen battery.
If the machine is going to be operated in excessively
cold conditions, a larger cold cranking amp battery
may be needed to ensure proper and prompt
starting. Never use jumper cables in a confi ned or
unventilated area. Battery acid fumes are explosive.
Battery acid can cause severe burns. Never expose
an open fl ame or spark near the battery. Keep all
burning materials away from the battery. When
servicing the battery, shield eyes and face, and do
not smoke. Service in a well ventilated area.
DANGER
!
WARNING
!
DANGER
!
DO NOT operate this machine indoors! Exhaust
fumes can be fatal. Never refuel while the machine is
running. Never refuel in the shop or building. Always
refuel in a well ventilated area, away from sparks
or open fl ames, DO NOT SMOKE. Extinguish all
smoking materials. Wipe up all spilled fuel before
restarting the engine. Do not fi ll above 1/2” (12.7mm)
from top of tank for diesel engines and 2” (50mm)
from the top of the tank for gasoline engines.
To obtain the most from your machine, for the least
amount of cost, it is a good practice to set up and follow
a scheduled preventative maintenance program. It will
eliminate many possible problems and down time.