B&D Controll-A-Door P Diamond SDO-2v2 Скачать руководство пользователя

Страница: 36 / 38

Optional Accessories

There is a range of additional accessories for your added convenience and security.

•

Safety Beams

- Part No 062734. Gives additional protection if the door is closing onto your property or person.

Simply breaking the beam “stops” the door! Must be

tted if the Auto-Close feature is operational.

•

Keyring Transmitter

- Part No 062731. Ideal for personal use when entry into the house may be via the garage.

•

Transmitter Wall Button

- Part No 062733. Allows you to operate the opener within 10 metres of the door. Ideal

for mounting inside the house.

•

Combo Access Kit

- Part No 062738. Keyswitch function will open the door without a transmitter. Can be used to

manually disengage the opener, and recommended when the garage door is the only access to the garage.

•

Remote Aerial Kit

- Part No 062177. For sites where radio range may be reduced.

Contact your Approved Dealer for installation of these accessory items.

When installing any accessories, always follow the instructions included with the product.

Only B&D accessories purchased from an Approved Dealer offer the highest quality and assure you of

trouble free opener operation.

Controll-A-Door

Diamond SDO-2v2

Instruction Manual

Содержание Controll-A-Door P Diamond SDO-2v2






































Результаты поиска

Содержание Controll-A-Door P Diamond SDO-2v2

Отзывы:

Похожие инструкции для Controll-A-Door P Diamond SDO-2v2

Бренды по названию

Популярные бренды

B&D Controll-A-Door P Diamond SDO-2v2, Инструкция по эксплуатации

Результаты поиска

Содержание Controll-A-Door P Diamond SDO-2v2

Отзывы:

Похожие инструкции для Controll-A-Door P Diamond SDO-2v2

Бренды по названию

Популярные бренды