background image

Warranty

(b)  instructions - failure to observe any instructions or directions (including “warning” noti

fi

 cations in the 

Instruction Manual), provided with the Product or given to you;
(c)  other devices - the Product being 

fi

 tted to any door or other closing device which is not of the type or 

condition de

fi

 ned in the Instruction Manual as suitable for installation of the Product;

(d)  installation or adjustment - faulty installation or adjustment of the Product or door to which the Product is 
connected where such installation or adjustment is not carried out by B&D or its approved distributors;
(e)  unauthorised acts - modi

fi

 cations or repairs made or attempted to be made by you or any unauthorised 

person;
(f) 

service - lack of proper maintenance, service or care of the door and Product;

(g)  outside control - events or acts beyond the reasonable control of B&D;
(h)  settings - use with doors locked or operation of the Product with excessively high opening or closing force 
settings
(i) 

wiring - faulty electrical wiring of structures to which the Product is af

fi

 xed; 

(j) 

interference - radio (including citizen brand transmissions) or other electronic interference;

(k)  water damage  - including effects from rust and corrosion); 
(l) 

salt - salt corrosion or damage to the surface coatings or base materials due to environmental conditions 

(such as proximity to the sea-front or similar corrosive conditions).
(m)  continuous operating time - maximum continuous operating time exceeding 1 minute in 10;
(n)  maximum operating force – the operating force exceeding 15kg* (150 Newton) when moving the door 
manually to the open or closed position;
(o)  door size – the door surface area exceeding 16.5m2;
(p) modi

fi

 cations - any unauthorised modi

fi

 cation to the Product;

(q)  insects damage - damage caused by insects; or
(r) 

non-residential use – installation of a residential garage door opener in a commercial or industrial premises 

or in a dwelling other than a single-family dwelling.

Statutory guarantees or warranties – 

Australia 
If you are a consumer under the Australian Consumer Law, our goods come with guarantees that cannot be 
excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and 
for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods 
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty certi

fi

 cate and other statements contained in this document or other B&D documents given to you 

do not exclude, restrict or modify the application of all or any of the provisions of the Australian Consumer Law.
New Zealand
This warranty certi

fi

 cate and other statements contained in this document or other B&D documents given to 

you do not exclude, restrict or modify the application of the New Zealand Consumer Guarantees Act (collectively 
de

fi

 ned as the “Act’); or the exercise of rights conferred by other statutory provisions which cannot be excluded, 

restricted or modi

fi

 ed, provided that to the extent that the Act or other statutory provision permits B&D to limit its 

liability for a breach of a statutory guarantee or warranty, B&D’s liability for such breach is limited to the payment 
of the cost of replacing the Product or acquiring an equivalent Product or repairing the Product.
In Australia, this warranty is given by B&D Australia Pty Limited (ABN 25 010 473 971) of B&D Doors of 34 
– 36 Marigold St, Revesby NSW 2212, phone 13 62 63 and email [email protected]. In New Zealand, this 
warranty is given by BD Doors (NZ) Limited of 30C Allens Road, East Tamaki, Auckland, phone 09-273 8600 and 
email [email protected] 

This warranty document is not intended to create a contract between B&D and the purchaser.

NOTES:
1. 

* The door that the Product is used with should be balanced in such a way that the user is able to open or 

close the door manually using a force not greater than 150 Newton (15 kg), other than to initially cause the door to 
start moving, which may require force in excess of that speci

fi

 ed in this paragraph.

Diamond PD Power Drive : Instruction Manual

© Copyright 2012 B&D Doors

35

Controll-A-Door

®

 P

 

Diamond SDO-2v2

 

Instruction Manual

Содержание Controll-A-Door P Diamond SDO-2v2







































Отзывы: