B&D Controll-A-Door P Diamond SDO-2v2 Скачать руководство пользователя

Страница: 31 / 38

If You Need a Service Call

If the opener needs service please call the dealer who
installed the garage door opener (for product assistance
contact 13 62 63 within Australia).

BEFORE CALLING

you should have the following

information to assist in providing the appropriate service:

1. Has anything happened since the opener last

operated OK, e.g. a storm, a jolt to the door etc.?

2.  How easy is it to manually open and close the door?
3.  What model is the opener?
4.  Who installed the opener?
5.  When was it installed?

Fault Indicator

When a fault is detected the SERVICE LED will start to

ash

and a number of beeps will sound to indicate that there is a
fault. The fault will be active each time an attempt is made
to operate the door.

Pressing the LIMIT SET button will reset the opener. If the
fault continues to be tripped contact an Approved Dealer
for assistance.

Troubleshooting Guide

Symptom

Possible cause

Remedy

The opener does not work from the
transmitter

Garage door in poor condition e.g.
springs may be broken

The opener does not have power

The battery in the transmitter is

The opener has been put into
“Vacation Mode”

The transmitter code has not been
set

Check the door’s operation - see
monthly maintenance (Page 30)

Plug a device e.g. a lamp, into the
power point and check that it is OK

Replace the battery (Page 28)

Turn off “Vacation Mode” (Page 19)

See coding transmitter procedure
(Page 18)

The motor runs but the door does
not move

The opener is disengaged

Re-engage the opener (Page 28)

The transmitter range varies or is
restricted

Variations are normal depending
on conditions e.g. temperature or
external interference

The battery is

at or faulty

Position of the transmitter in the
motor vehicle

See instructions for correct use of
transmitter (Page 27)

Replace the battery (Page 28)

Change the position (Page 27)

The light does not work

Light module is not inserted/
connected properly

Check for correct connection
otherwise contact your dealer for
support

The door reverses for no apparent
reason

This may occur occasionally from
weather changes

The opener automatically adjusts to
compensate for changes, to adjust
the force see (Page 17)

The door opens but will not close

Safety Beam not operating correctly

Check the installation (Page 21-24)
otherwise contact your dealer for
support

The unit has started to beep and

ashing

The service reminder has been
triggered

Contact your dealer and arrange
a door service. Alternatively press
LIMIT SET button to reset the
service counter.

Diamond PD Power Drive : Instruction Manual

Controll-A-Door

Diamond SDO-2v2

Instruction Manual

Содержание Controll-A-Door P Diamond SDO-2v2






































Результаты поиска

Содержание Controll-A-Door P Diamond SDO-2v2

Отзывы:

Похожие инструкции для Controll-A-Door P Diamond SDO-2v2

Бренды по названию

Популярные бренды

B&D Controll-A-Door P Diamond SDO-2v2, Инструкция по эксплуатации

Результаты поиска

Содержание Controll-A-Door P Diamond SDO-2v2

Отзывы:

Похожие инструкции для Controll-A-Door P Diamond SDO-2v2

Бренды по названию

Популярные бренды