B&B Electronics e-Linx EIRP610-2SFP-T Скачать руководство пользователя страница 114

Страница: 114 / 147

Web-Based Management

6.26.4 MAC Address Table

—Multicast Filtering

Multicasts are similar to broadcasts, they are sent to all end stations on a LAN or VLAN.

Multicast filtering is the function, which end stations can receive the multicast traffic if the

connected ports had been included in the specific multicast groups. With multicast filtering,

network devices only forward multicast traffic to the ports that are connected to the

registered end stations.



IP Address

: Assign a multicast group IP address in the range of 224.0.0.0 ~

239.255.255.255.



Member Ports

: Tick the check box beside the port number to include them as the

member ports in the specific multicast group IP address.



Click

Add

to append a new filter of multicast to the field, or select the filter in the

field and click

Delete

to remove it.

Multicast Filtering interface

108

Manual Documentation Number EIRP610-2SFP-T

– 0912m

www.bb-elec.com

www.bb-europe.com

Содержание e-Linx EIRP610-2SFP-T




















































































































































Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды

B&B Electronics e-Linx EIRP610-2SFP-T, Руководство пользователя

Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды