B&B Electronics e-Linx EIRP610-2SFP-T Скачать руководство пользователя страница 115

Страница: 115 / 147

Web-Based Management

6.27 Power over Ethernet

This segment shows the Power over Ethernet function.

PoE Status



Maximum Power Available:

Displays the maximum power supply in Watt.



Actual Power Consumption:

This column shows the real-time total power

consumption.



System Power Limit:

User can modify the value to this column field to limit the total

output power for the system.



Main Supply Voltage:

This column shows the output voltage of the system for PoE

ports.



Firmware Version:

This column shows the PoE chip‘s firmware version.



Port Knockoff Disabled:

Power Management state where one or more PDs have been

powered down so that a higher priority PD may be powered up and not yet exceed the

109

Manual Documentation Number EIRP610-2SFP-T

– 0912m

www.bb-elec.com

www.bb-europe.com

Содержание e-Linx EIRP610-2SFP-T




















































































































































Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды

B&B Electronics e-Linx EIRP610-2SFP-T, Руководство пользователя

Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды