B&B Electronics e-Linx EIRP610-2SFP-T Скачать руководство пользователя страница 109

Страница: 109 / 147

Web-Based Management

6.25.2 Port Configuration

You can configure the 802.1x authentication state for each port. The state provides Disable,

Accept, Reject, and Authorize.



Reject:

The specified port is required to be held in the unauthorized state.



Accept:

The specified port is required to be held in the authorized state.



Authorize:

The specified port is set to the Authorized or Unauthorized state in

accordance with the outcome of an authentication exchange between the Supplicant

and the authentication server.



Disable:

When disabled, the specified port works without complying with 802.1x

protocol.



Click

Apply

802.1x Per Port Setting interface

103

Manual Documentation Number EIRP610-2SFP-T

– 0912m

www.bb-elec.com

www.bb-europe.com

Содержание e-Linx EIRP610-2SFP-T




















































































































































Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды

B&B Electronics e-Linx EIRP610-2SFP-T, Руководство пользователя

Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды