B&B Electronics e-Linx EIRP610-2SFP-T Скачать руководство пользователя страница 64

Страница: 64 / 147

Web-Based Management

6.14 Port Control

In Port control you can configure the settings of each port to control the connection

parameters. The status of each port is listed beneath.



Port:

Use the scroll bar and click on the port number to choose the port to be

configured.



State:

Current port state. The port can be set to disable or enable mode. If the port state

is set as ‗Disable‘, it will not receive or transmit any packet.



Negotiation:

Auto and Force. Being set as Auto, the speed and duplex mode are

negotiated automatically. When you set it as Force, you have to set the speed and

duplex mode manually.



Speed:

It is available for selecting when the Negotiation column is set as Force. When

the Negotiation column is set as Auto, this column is read-only.



Duplex:

It is available for selecting when the Negotiation column is set as Force.

When the Negotiation column is set as Auto, this column is read-only.



Flow Control:

Whether or not the receiving node sends feedback to the sending node

is determined by this item. When enabled, once the device exceeds the input data rate

of another device, the receiving device will send a PAUSE frame which halts the

transmission of the sender for a specified period of time. When disabled, the receiving

device will drop the packet if too much to process.



Security:

When the Security selection is set as ‗

‘, any access from the device which

connects to this port will be blocked unless the MAC address of the device is included

in the static MAC address table. See the segment of

MAC Address Table—Static

MAC Addresses



Click

Apply

to have the configuration take effect.

Manual Documentation Number EIRP610-2SFP-T

– 0912m

www.bb-elec.com

www.bb-europe.com

Содержание e-Linx EIRP610-2SFP-T




















































































































































Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды

B&B Electronics e-Linx EIRP610-2SFP-T, Руководство пользователя

Результаты поиска

Содержание e-Linx EIRP610-2SFP-T

Отзывы:

Похожие инструкции для e-Linx EIRP610-2SFP-T

Бренды по названию

Популярные бренды