Balluff BNI PNT-508-005-E002 Скачать руководство пользователя страница 8

Страница: 8 / 48

Balluff Network Interface

ProfiNet™

www.balluff.com

First Steps

3.2.

Mechanical
Connection

The module is secured by means of two M6 screws and two washers.

3.3.

Electrical
Connection

Power supply

Power supply "INPUT" (7/8", connector)

Pin

Function

Description

Bus/sensor and actuator power
supply ground

0 V

2
3

Function ground

Bus/sensor power supply

+24 V

Actuator power supply

+24 V

Power supply "OUTPUT" (7/8", female)

Pin

Function

Description

Bus/sensor and actuator power
supply ground

0 V

2
3

Function ground

Bus/sensor power supply

+24 V

Actuator power supply

+24 V

Note

Where possible, use separate power supplies for sensor/bus and actuator.
Total current < 9 A The total current of all modules must not exceed 9 A even in
the case of series connection of the actuator supply.

Grounding

Note

The function ground connection from the housing to the machine must have
low-impedance and is made using the mounting screw.

PROFINET
interface

M12, D-coded, female

Pin

Function

Tx+

Transmit Data +

Rx+

Receive Data +

Tx-

Transmit Data -

Rx-

Receive Data -

Note

Unused I/O ports must be provided with cover caps to comply with degree of
protection IP69.

Содержание BNI PNT-508-005-E002

















































Результаты поиска

Содержание BNI PNT-508-005-E002

Отзывы:

Похожие инструкции для BNI PNT-508-005-E002

Бренды по названию

Популярные бренды

Balluff BNI PNT-508-005-E002, Руководство пользователя

Результаты поиска

Содержание BNI PNT-508-005-E002

Отзывы:

Похожие инструкции для BNI PNT-508-005-E002

Бренды по названию

Популярные бренды