Bailey Infi 90 IMDSM05 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 46

Bailey Infi 90 IMDSM05 Скачать руководство пользователя страница 22

INSTALLATION

SETUP

I-E96-309A

3 - 3

The enable switch allows the DSM to use the address selection
switch to set addresses for LMM/MFP operation. The address
is set by an eight position address dipswitch shown in Figure

.

Enable Switch (MFP/LMM)

When the DSM communicates with the MFP, the right contact
of the enable switch must be set to the 1 or open position for
the module to respond. Set the 6-bit address of the DSM on
contacts 3-8 on the address selection switch. Table

the addresses that are possible for each group.

Slave Address Selection Switch (MFP/LMM)

The DSM can have one of 64 addresses (address 0 to 63) on the
slave expander bus (20 slaves maximum). This address
uniquely identifies the slave to the master module and must be
the same as the address set in the master module configura-
tion (Function Code 84 specification 1).

Figure 3-2. Address and Enable Switches

ENABLE
SWITCH

ADDRESS SELECTION

SWITCH

MODULE CONFIGURATION

SWITCH

I/O

JUMPERS

(J1-J16)

DEFAULT VALUE

SWITCHES

TP35702A

1

1

2

OPEN

OPEN

8

1

OPEN

8

1

OPEN

2

1

OPEN

8

1

OPEN

8

1

OPEN

4

J17

J18

J3

J1

J4

J2

J7

J8

J5

J6

J10

J13

J14

J9

3

1

2

3

1

2

3

1

2

3
2
1

J11

3
2
1

J12

3
2
1

J15

3
2
1

J16

3
2
1

3
2
1

3
2
1

3
2
1

3
2
1

3
2
1

3
2
1

3
2
1

3
2
1

1

1

2

2

3

3

0

DISABLE

ENABLE CONTACTS 5-8
ON ADDRESS SWITCH

ENABLE CONTACTS 1-4
ON ADDRESS SWITCH

SET CONTACTS 3-8 FOR
MFP/LMM ADDRESS

1

ENABLE

«
...
20
21
22
23
24
...
»

Содержание Infi 90 IMDSM05















































Отзывы:

Нет отзывов