Bailey Infi 90 IMDSM05 Скачать руководство пользователя страница 21

Страница: 21 / 46

INSTALLATION

SETUP

3 - 2

I-E96-309A

SETUP

Prior to installation, set the address of the DSM and install
jumpers to configure the digital outputs and inputs. Be sure
you configure the termination unit (TU) or termination module
(TM) to accept the field device signals. Figure

3-1

shows the 5

switches and 18 jumpers to set on the DSM. The module
switches and jumpers are:

•

An address switch and an enable switch determine the
address bytes that precede every data transfer (one module
address byte for the MFP/LMM).

•

A module configuration switch sets the output to the exist-
ing or default value during a communication break with the
master.

•

Two default value switches set the default value of the A
group and B group outputs.

•

Two master selection jumpers select a LMM or MFP master
for the DSM.

•

Sixteen two-position jumpers set outputs for two-wire iso-
lated or normal output operation.

Figure 3-1. Switches and Jumpers

ENABLE
SWITCH

ADDRESS

SELECTION

SWITCH

MODULE CONFIGURATION

SWITCH

I/O

JUMPERS

(J1-J16)

MASTER

SELECTION

JUMPERS

DEFAULT VALUE

SWITCHES

TP35704A

OPEN

J17

J18

J10

J13

J14

3
2
1

J11

3
2
1

J12

3
2
1

J15

3
2
1

J16

3
2
1

Содержание Infi 90 IMDSM05















































Результаты поиска

Содержание Infi 90 IMDSM05

Отзывы:

Похожие инструкции для Infi 90 IMDSM05

Бренды по названию

Популярные бренды

Bailey Infi 90 IMDSM05, Инструкция

Результаты поиска

Содержание Infi 90 IMDSM05

Отзывы:

Похожие инструкции для Infi 90 IMDSM05

Бренды по названию

Популярные бренды